Merge tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes

Fixes for omaps for v5.15

Few regression fixes for omaps for the v5.15-rc cycle. There is a fix
for boot time hangs that can happen on some am335x devices that started
when the pruss devicetree nodes were added. The other fixes are less
critical:

- Fix compiler warning for sysc_init_soc() that got recently introduced

- Fix external abort for am335x pruss as otherwise some am335x will hang

- Use CLKDM_NOAUTO quirk also for dra7 dcan1

- Fix older NAND device node regression for omap3-sdp

* tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap3430-sdp: Fix NAND device node
  bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
  soc: ti: omap-prm: Fix external abort for am335x pruss
  bus: ti-sysc: Add break in switch statement in sysc_init_soc()

Link: https://lore.kernel.org/r/pull-1633609552-789682@atomide.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 5.15, round 2:

- A couple of fixes from Haibo Chen to update SPI NOR TX bus width for
  i.MX6 and i.MX8 boards.  This becomes necessary because spi-nor driver
  starts using the setting in DT.
- Mark buck2 always-on for i.MX8MM Kontron-n801x-som board to avoid the
  core supply being turned off unexpectedly.
- Fix eSDHC2 device tree settings for LS1028A SoC.
- Disable GIC CPU interface before calling stby-poweroff sequence to fix
  power-off failure on i.MX6.
- Fix M2_RST# GPIO pinmux on i.MX8M venice-gw7902 boards.

* tag 'imx-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
  ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
  arm64: dts: ls1028a: fix eSDHC2 node
  arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
  arm64: dts: imx8: change the spi-nor tx
  ARM: dts: imx: change the spi-nor tx

Link: https://lore.kernel.org/r/20211006125734.GA10197@dragonSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Nand is on CS1 so reg properties first field should be 1 not 0.

Fixes: 44e47164 ("ARM: dts: omap3: Fix NAND device nodes")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 94f63457 ("bus: ti-sysc: Implement quirk handling for
CLKDM_NOAUTO") should have also added the quirk for dra7 dcan1 in
addition to dcan2 for errata i893 handling.

Let's also pass the quirk flag for legacy mode booting for if "ti,hwmods"
dts property is used with related dcan hwmod data. This should be only
needed if anybody needs to git bisect earlier stable trees though.

Fixes: 94f63457 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO")
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge in a fix for pruss reset issue caused by enabling pruss for am335x.

gcc warns that accessing a pointer based on a numeric constant may
be an offset into a NULL pointer, and would therefore has zero
accessible bytes:

arch/arm/common/sharpsl_param.c: In function ‘sharpsl_save_param’:
arch/arm/common/sharpsl_param.c:43:9: error: ‘memcpy’ reading 64 bytes from a region of size 0 [-Werror=stringop-overread]
   43 |         memcpy(&sharpsl_param, param_start(PARAM_BASE), sizeof(struct sharpsl_param_info));
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

In this particular case, the warning is bogus since this is the actual
pointer, not an offset on a NULL pointer. Add a local variable to shut
up the warning and hope it doesn't come back.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99578
Link: https://lore.kernel.org/r/20210927145332.2784005-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 5.15:

- Revert cc8870bf to fix the regression on i.MX6 that suspend
  support becomes broken.
- Add `qca,clk-out-frequency` property to fix Ethernet support on
  imx6qdl-pico board.
- Re-enable FB support in imx_v6_v7_defconfig.  It gets lost due to
  f611b1e7 ("drm: Avoid circular dependencies for CONFIG_FB").
- Fix LP5562 LED support on imx6dl-yapp4 board.
- Add missing pinctrl-names for panel on M53Menlo board.
- Fix USB host power regulator polarity on M53Menlo board.

* tag 'imx-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx_v6_v7_defconfig: enable fb
  ARM: dts: imx6qdl-pico: Fix Ethernet support
  ARM: dts: imx: Fix USB host power regulator polarity on M53Menlo
  ARM: dts: imx: Add missing pinctrl-names for panel on M53Menlo
  Revert "ARM: imx6q: drop of_platform_default_populate() from init_machine"
  ARM: dts: imx6dl-yapp4: Fix lp5562 LED driver probe

Link: https://lore.kernel.org/r/20210923063356.GK13480@dragonSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The framebuffer is gone on the D-Link DIR-685, restore it.

Fixes: f611b1e7 ("drm: Avoid circular dependencies for CONFIG_FB")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210922200933.1825752-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This can cause a randconfig warning without the 'inline' flag
that every other platform uses:

In file included from arch/arm/boot/compressed/misc.c:29:
arch/arm/mach-dove/include/mach/uncompress.h:14:13: error: 'putc' defined but not used [-Werror=unused-function]
   14 | static void putc(const char c)
      |             ^~~~
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210927095343.1015422-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Commit 38225f2e ("ARM/omap1: switch to use dma_direct_set_offset for
lbus DMA offsets") removed a lot of mach/memory.h, but left the USB
offset handling split into arch/arm/mach-omap1/usb.c and
drivers/usb/host/ohci-omap.c.

This can cause a randconfig build warning that now fails the build
with -Werror:

arch/arm/mach-omap1/usb.c:561:30: error: 'omap_1510_usb_ohci_nb' defined but not used [-Werror=unused-variable]
  561 | static struct notifier_block omap_1510_usb_ohci_nb = {
      |                              ^~~~~~~~~~~~~~~~~~~~~

Move it all into the platform file to get rid of the final
location that relies on mach/memory.h.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210927144118.2464881-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-drivers-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes

Qualcomm driver fixes for v5.15

This restricts the QCOM_SCM driver to depend on ARCH_QCOM, to reduce
it's presence after becoming a loadable module.

It then fixes a regression in the mdt_loader, where firmware with the
hash segment marked as PT_LOAD would no longer be accepted, preventing
several MSM8974 and SDM660 devices from loading remoteproc firmware.

Lastly it corrects the drvdata associated with the socinfo device during
probe, to match that expected by the remove function.

* tag 'qcom-drivers-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  firmware: qcom_scm: QCOM_SCM should depend on ARCH_QCOM
  soc: qcom: mdt_loader: Drop PT_LOAD check on hash segment
  soc: qcom: socinfo: Fixed argument passed to platform_set_data()

Link: https://lore.kernel.org/r/20210930025456.1035-1-bjorn.andersson@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-arm64-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes

Qualcomm ARM64 DTS fixes for 5.15

This starts by reverting the SC7280 CPUfreq update, which was merged
before concensus about the associated drivers changes was reached.

It then moves the reserved-memory changes done to get IPA working on the
Lenovo Yoga C630 into the Yoga specific DTS, as changing the memory map
on the platform level did break a couple of the other boards.

It fixes the HDMI audio on Trogdor and add missing Aggre2 NOC qos clocks
on SDM6{30,36,60} which prevented some boards from booting.

Lastly it enables the PON module on SM8250/QRB5165, as the lack thereof
is blocking automated testing in LKFT.

* tag 'qcom-arm64-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  arm64: dts: qcom: sdm630: Add missing a2noc qos clocks
  arm64: dts: qcom: qrb5165-rb5: enabled pwrkey and resin nodes
  arm64: dts: qcom: pm8150: specify reboot mode magics
  arm64: dts: qcom: pm8150: use qcom,pm8998-pon binding
  arm64: dts: qcom: sc7180-trogdor: Fix lpass dai link for HDMI
  arm64: dts: qcom: sdm850-yoga: Reshuffle IPA memory mappings
  Revert "arm64: dts: qcom: sc7280: Fixup the cpufreq node"

Link: https://lore.kernel.org/r/20210930025509.1091-1-bjorn.andersson@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'juno-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes

 Juno/Vexpress fixes for v5.15

Bunch of DTS fixes to resolve addressing issues with some of the device
nodes, dropping unused/undocumented properties in various nodes, and
aligning node names with dtschema.

* tag 'juno-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  arm: dts: vexpress: Fix motherboard bus 'interrupt-map'
  arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes
  arm: dts: vexpress-v2p-ca9: Fix the SMB unit-address
  arm: dts: vexpress: Drop unused properties from motherboard node
  arm64: dts: arm: drop unused interrupt-names in MHU
  ARM: dts: arm: align watchdog and mmc node names with dtschema
  arm64: dts: arm: align watchdog and mmc node names with dtschema
  arm64: dts: fvp: Remove panel timings

Link: https://lore.kernel.org/r/20210927105249.3583380-1-sudeep.holla@arm.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-dts-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes

Qualcomm DTS fixes for v5.15

This corrects the use of depricated chipid and clock names, for which
support was finally dropped from the driver. It also ensures that the
DSI PLL is fed by the correct clock, now that it's being migrated to not
rely on global clock names.

* tag 'qcom-dts-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  ARM: dts: qcom: apq8064: update Adreno clock names
  ARM: dts: qcom: apq8064: Use 27MHz PXO clock as DSI PLL reference
  ARM: dts: qcom: apq8064: use compatible which contains chipid

Link: https://lore.kernel.org/r/20210930025526.1146-1-bjorn.andersson@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'at91-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes

AT91 fixes #2 for 5.15:

- More fixes for AT91 platform power management code related to the
  introduction of sama7g5:
  - management of DDR3L regulator rails for sama7g5ek
  - loading of TLB on different cores

- PIO controller slew-rate settings for sama7g5ek: be aligned with
  datasheet requirements.

* tag 'at91-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
  ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
  ARM: at91: pm: preload base address of controllers in tlb
  ARM: at91: pm: group constants and addresses loading
  ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail

Link: https://lore.kernel.org/r/20211004114344.19304-1-nicolas.ferre@microchip.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Add Vignesh to TI K3 platform maintainership. We will rotate roles for
each kernel version to help spread the work load a little better.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210915121308.26795-1-nm@ti.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'optee-fix-for-v5.15' of git://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes

Fix OP-TEE shm_pool lint warning

* tag 'optee-fix-for-v5.15' of git://git.linaro.org/people/jens.wiklander/linux-tee:
  tee/optee/shm_pool: fix application of sizeof to pointer

Link: https://lore.kernel.org/r/20210915113813.GA509196@jadeSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Fix invalid M2_RST# gpio pinmux.

Fixes: ef484dfc ("arm64: dts: imx: Add i.mx8mm/imx8mn Gateworks gw7902 dts support")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Any pending interrupt can prevent entering standby based power off state.
To avoid it, disable the GIC CPU interface.

Fixes: 8148d213 ("ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" is set")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On the LS1028A this instance of the eSDHC controller is intended for
either an eMMC or eSDIO card. It doesn't provide a card detect pin and
its IO voltage is fixed at 1.8V.

Remove the bogus broken-cd property, instead add the non-removable
property. Fix the voltage-ranges property and set it to 1.8V only.

Fixes: 491d3a3f ("arm64: dts: ls1028a: Add esdhc node in dts")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The buck2 output of the PMIC is the VDD core voltage of the cpu.
Switching off this will poweroff the CPU. Add the 'regulator-always-on'
property to avoid this.

Fixes: 8668d8b2 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

With commit c709135e ("pinctrl: at91-pio4: add support for slew-rate")
and commit cbde6c82 ("pinctrl: at91-pio4: Fix slew rate disablement")
the slew-rate is enabled by default for each configured pin. The datasheet
specifies at chapter "Output Driver AC Characteristics" that HSIO
drivers (use in SDMMCx and QSPI0 peripherals), don't have a slewrate
setting but are rather calibrated against an external 1% resistor mounted
on the SDMMCx_CAL or QSPI0_CAL pins. Depending on the target signal
frequency and the external load, it is possible to adjust their target
output impedance. Thus set slew-rate = <0> for SDMMC (QSPI is not enabled
at the moment in device tree).

Fixes: 7540629e ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-3-claudiu.beznea@microchip.com

Datasheet chapter "EMAC Timings" specifies that while in 3.3V domain
GMAC's MDIO pins should be configured with slew-rate enabled, while the
data + signaling pins should be configured with slew-rate disabled when
GMAC works in RGMII or RMII modes. The pin controller for SAMA7G5 sets
the slew-rate as enabled for all pins. Adapt the device tree to comply
with these.

Fixes: 7540629e ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-2-claudiu.beznea@microchip.com

In suspend/resume procedure for AT91 architecture different controllers
(PMC, SHDWC, RAM, RAM PHY, SFRBU) are accessed to do the proper settings
for power saving. Commit f0bbf179 ("ARM: at91: pm: add self-refresh
support for sama7g5") introduced the access to RAMC PHY controller for
SAMA7G5. The access to this controller is done after RAMC ports are
closed, thus any TLB walk necessary for RAMC PHY virtual address will
fail. In the development branch this was not encountered. However, on
current kernel the issue is reproducible.

To solve the issue the previous mechanism of pre-loading the TLB with
the RAMC PHY virtual address has been used. However, only the addition
of this new pre-load breaks the functionality for ARMv5 based
devices (SAM9X60). This behavior has been encountered previously
while debugging this code and using the same mechanism for pre-loading
address for different controllers (e.g. pin controller, the assumption
being that other requested translations are replaced from TLB).

To solve this new issue the TLB flush + the extension of pre-loading
the rest of controllers to TLB (e.g. PMC, RAMC) has been added. The
rest of the controllers should have been pre-loaded previously, anyway.

Fixes: f0bbf179 ("ARM: at91: pm: add self-refresh support for sama7g5")
Depends-on: e42cbbe5 ("ARM: at91: pm: group constants and addresses loading")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-4-claudiu.beznea@microchip.com

Group constants and addresses loading. This commit prepares the field for
the next one.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-3-claudiu.beznea@microchip.com

SAMA7G5-EK board has DDR3L type of memory soldered. This needs 1.35V. The
1.35V for DDR3L rail at run-time is selected by the proper configuration
on SELV2 pin (for 1.35V it needs to be in high-z state). When suspended
the MCP16502 PMIC soldered on SAMA7G5-EK will use different sets of
configuration registers to provide proper voltages on its rail. Run-time
configuration registers could be configured differently than suspend
configuration register for MCP16502 (VSEL2 affects only run-time
configuration). In suspend states the DDR3L memory soldered on SAMA7G5-EK
switches to self-refresh. Even on self-refresh it needs to be powered by
a 1.35V rail. Thus, make sure the PMIC is configured properly when system
is suspended.

Fixes: 7540629e (ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-2-claudiu.beznea@microchip.com

Before commit 0e30f472 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.

qspi and fspi host controller do not support read 1-4-4 mode. so need to
set the tx to 1, let the common code finally select read 1-1-4 mode.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 0e30f472 ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Before commit 0e30f472 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.

Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board
do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also
impact the read mode selection. For the spi-nor device on the upper mentioned
boards, they support read 1-4-4 mode and read 1-1-4 mode according to the
device internal sfdp register. But qspi host controller do not support
read 1-4-4 mode. so need to set the tx to 1, let the common code finally
select read 1-1-4 mode, PP-1-1-1 mode.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 0e30f472 ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Starting with v5.15-rc1, we may now see some am335x beaglebone black
device produce the following error on pruss probe:

Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0326000

This has started with the enabling of pruss for am335x in the dts files.

Turns out the is caused by the PRM reset handling not waiting for the
reset bit to clear. To fix the issue, let's always wait for the reset
bit to clear, even if there is a separate reset status register.

We attempted to fix a similar issue for dra7 iva with a udelay() in
commit effe89e4 ("soc: ti: omap-prm: Fix occasional abort on reset
deassert for dra7 iva"). There is no longer a need for the udelay()
for dra7 iva reset either with the check added for reset bit clearing.

Cc: Drew Fustini <pdp7pdp7@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Yongqin Liu <yongqin.liu@linaro.org>
Fixes: effe89e4 ("soc: ti: omap-prm: Fix occasional abort on reset deassert for dra7 iva")
Reported-by: Matti Vaittinen <mazziesaccount@gmail.com>
Tested-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 078fb7aa ("arm: dts: vexpress: Fix addressing issues with
'motherboard-bus' nodes") broke booting on a couple of 32-bit VExpress
boards. The problem is #address-cells size changed, but interrupt-map
was not updated. This results in the timer interrupt (and all the
other motherboard interrupts) not getting mapped.

As the 'interrupt-map' properties are all just duplicates across boards,
just move them into vexpress-v2m.dtsi and vexpress-v2m-rs1.dtsi.
Strictly speaking, 'interrupt-map' is dependent on the parent
interrupt controller, but it's not likely we'll ever have a different
parent than GICv2 on these old platforms. If there was one,
'interrupt-map' can still be overridden.

Link: https://lore.kernel.org/r/20210924214221.1877686-1-robh@kernel.org
Fixes: 078fb7aa ("arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes")
Cc: Guillaume Tucker <guillaume.tucker@collabora.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Reported-by: Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

It adds the missing a2noc clocks required for QoS registers programming
per downstream kernel[1].

[1] https://source.codeaurora.org/quic/la/kernel/msm-4.4/tree/arch/arm/boot/dts/qcom/sdm660-bus.dtsi?h=LA.UM.8.2.r1-04800-sdm660.0#n43

Fixes: 045547a0 ("arm64: dts: qcom: sdm630: Add interconnect provider nodes")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210824043435.23190-4-shawn.guo@linaro.org

Enable powerkey and resin nodes to let the board handle POWER and
Volume- keys properly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210916151341.1797512-3-dmitry.baryshkov@linaro.org

Specify recovery and bootloader magic values to be programmed by the
qcom-pon driver. This allows the bootloader to handle
reboot-to-bootloader functionality.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210916151341.1797512-2-dmitry.baryshkov@linaro.org

Change pm8150 to use the qcom,pm8998-pon compatible string for the pon
in order to pass reboot mode properly.

Fixes: 5101f22a ("arm64: dts: qcom: pm8150: Add base dts file")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210916151341.1797512-1-dmitry.baryshkov@linaro.org

Enable CONFIG_FB which is nowadays required for CONFIG_DRM_PANEL_LVDS,
CONFIG_DRM_PANEL_SIMPLE, CONFIG_DRM_PANEL_SEIKO_43WVF1G,
CONFIG_FB_MODE_HELPERS, CONFIG_BACKLIGHT_PWM, CONFIG_BACKLIGHT_GPIO,
CONFIG_FRAMEBUFFER_CONSOLE, CONFIG_LOGO, CONFIG_FONTS, CONFIG_FONT_8x8
and CONFIG_FONT_8x16.

Fixes: f611b1e7 ("drm: Avoid circular dependencies for CONFIG_FB")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently, it is no longer possible to retrieve a DHCP address
on the imx6qdl-pico board.

This issue has been exposed by commit f5d9aa79 ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").

Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.

Fixes: 98670a0b ("ARM: dts: imx6qdl: Add imx6qdl-pico support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The MIC2025 switch input signal nEN is active low, describe it as such
in the DT. The previous change to this regulator polarity was incorrectly
influenced by broken quirks in gpiolib-of.c, which is now long fixed. So
fix this regulator polarity setting here once and for all.

Fixes: 3c3601cd ("ARM: dts: imx53: Update USB configuration on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The panel already contains pinctrl-0 phandle, but it is missing
the default pinctrl-names property, so the pin configuration is
ignored. Fill in the missing pinctrl-names property, so the pin
configuration is applied.

Fixes: d81765d6 ("ARM: dts: imx53: Update LCD panel node on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This reverts commit cc8870bf.

Since commit cc8870bf ("ARM: imx6q: drop of_platform_default_populate()
from init_machine") the following errors are seen on boot:

[    0.123372] imx6q_suspend_init: failed to find ocram device!
[    0.123537] imx6_pm_common_init: No DDR LPM support with suspend -19!

, which break suspend/resume on imx6q/dl.

Revert the offeding commit to avoid the regression.

Thanks to Tim Harvey for bisecting this problem.

Cc: stable@vger.kernel.org
Fixes: cc8870bf ("ARM: imx6q: drop of_platform_default_populate() from  init_machine")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since the LED multicolor framework support was added in commit
92a81562 ("leds: lp55xx: Add multicolor framework support to lp55xx")
LEDs on this platform stopped working.

Author of the framework attempted to accommodate this DT to the
framework in commit b86d3d21 ("ARM: dts: imx6dl-yapp4: Add reg property
to the lp5562 channel node") but that is not sufficient. A color property
is now required even if the multicolor framework is not used, otherwise
the driver probe fails:

  lp5562: probe of 1-0030 failed with error -22

Add the color property to fix this.

Fixes: 92a81562 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Cc: <stable@vger.kernel.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>