- 16 Aug, 2021 26 commits
-
-
Aric Cyr authored
This version brings along following fixes: - Ensure DCN save init registers after VM setup - Fix multi-display support for idle opt workqueue - Use vblank control events for PSR enable/disable - Create default dc_sink when fail reading EDID under MST Acked-by:
Wayne Lin <wayne.lin@amd.com> Signed-off-by:
Aric Cyr <aric.cyr@amd.com> Tested-by:
Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Anthony Koo authored
Acked-by:
Anthony Koo <Anthony.Koo@amd.com> Tested-by:
-
Nicholas Kazlauskas authored
[Why] Compilation of the workqueue fails if not building with the DCN config option set. [How] Guard calls to the flush with the DCN config option to fix the build. Reviewed-by:
Roman Li <Roman.Li@amd.com> Acked-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by:
-
Jake Wang authored
[Why] DM initializes VM context after DMCUB initialization. This results in loss of DCN_VM_CONTEXT registers after z10. [How] Notify DMCUB when VM setup is complete, and have DMCUB save init registers. v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix Reviewed-by:
Jake Wang <haonan.wang2@amd.com> Tested-by:
-
Nicholas Kazlauskas authored
[Why] PSR can disable the HUBP along with the OTG when PSR is active. We'll hit a pageflip timeout when the OTG is disable because we're no longer updating the CRTC vblank counter and the pflip high IRQ will not fire on the flip. In order to flip the page flip timeout occur we should modify the enter/exit conditions to match DRM requirements. [How] Use our deferred handlers for DRM vblank control to notify DMCU(B) when it can enable or disable PSR based on whether vblank is disabled or enabled respectively. We'll need to pass along the stream with the notification now because we want to access the CRTC state while the CRTC is locked to get the stream state prior to the commit. Retain a reference to the stream so it remains safe to continue to access and release that reference once we're done with it. Enable/disable logic follows what we were previously doing in update_planes. The workqueue has to be flushed before programming streams or planes to ensure that we exit out of idle optimizations and PSR before these events occur if necessary. To keep the skip count logic the same to avoid FBCON PSR enablement requires copying the allow condition onto the DM IRQ parameters - a field that we can actually access from the worker. Reviewed-by:
-
Nicholas Kazlauskas authored
[Why] The current implementation for idle optimization support only has a single work item that gets reshuffled into the system workqueue whenever we receive an enable or disable event. We can have mismatched events if the work hasn't been processed or if we're getting control events from multiple displays at once. This fixes this issue and also makes the implementation usable for PSR control - which will be addressed in another patch. [How] We need to be able to flush remaining work out on demand for driver stop and psr disable so create a driver specific workqueue instead of using the system one. The workqueue will be single threaded to guarantee the ordering of enable/disable events. Refactor the queue to allocate the control work and deallocate it after processing it. Pass the acrtc directly to make it easier to handle psr enable/disable in a later patch. Rename things to indicate that it's not just MALL specific. Reviewed-by:
-
Wayne Lin authored
[Why] While reading remote EDID via Startech 1-to-4 hub, occasionally we won't get response in time and won't light up corresponding monitor. Ideally, we can still add generic modes for userspace to choose to try to light up the monitor and which is done in drm_helper_probe_single_connector_modes(). So the main problem here is that we fail .mode_valid since we don't create remote dc_sink for this case. [How] Also add default dc_sink if we can't get the EDID. Reviewed-by:
-
Evan Quan authored
These registers have different address from other SMU V11 ASICs. Signed-off-by:
Evan Quan <evan.quan@amd.com> Reviewed-by:
Lijo Lazar <lijo.lazar@amd.com> Signed-off-by:
-
Evan Quan authored
As the fan control was guarded under manual mode before fan speed RPM/PWM setting. Thus the extra check is totally redundant. Signed-off-by:
-
Evan Quan authored
Currently, the readout of fan speed pwm is transited into percent-based and then pwm-based. However, the transition into percent-based is totally unnecessary and make the final output less accurate. Signed-off-by:
-
Evan Quan authored
The relationship "PWM = RPM / smu->fan_max_rpm" between fan speed PWM and RPM is not true for SMU11 ASICs. So, we need a new way to retrieving the fan speed RPM. Signed-off-by:
-
Evan Quan authored
The relationship "PWM = RPM / smu->fan_max_rpm" between fan speed PWM and RPM is not true for SMU11 ASICs. So, we need a new way to retrieving the fan speed PWM. Signed-off-by:
-
Evan Quan authored
As the relationship "PWM = RPM / smu->fan_max_rpm" between fan speed PWM and RPM is not true for SMU11 ASICs. So, both the RPM and PWM settings need to be saved. Signed-off-by:
-
Evan Quan authored
The relationship "PWM = RPM / smu->fan_max_rpm" between fan speed PWM and RPM is not true for SMU11 ASICs. So, we need a new way to perform the fan speed RPM setting. Signed-off-by:
-
Candice Li authored
Delete ras_if->name in the RAS ctx structure and remove related lines. Signed-off-by:
Candice Li <candice.li@amd.com> Reviewed-by:
John Clements <john.clements@amd.com> Signed-off-by:
-
Yifan Zhang authored
KFDSVMRangeTest.SetGetAttributesTest randomly fails in stress test. Note: Google Test filter = KFDSVMRangeTest.* [==========] Running 18 tests from 1 test case. [----------] Global test environment set-up. [----------] 18 tests from KFDSVMRangeTest [ RUN ] KFDSVMRangeTest.BasicSystemMemTest [ OK ] KFDSVMRangeTest.BasicSystemMemTest (30 ms) [ RUN ] KFDSVMRangeTest.SetGetAttributesTest [ ] Get default atrributes /home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:154: Failure Value of: expectedDefaultResults[i] Actual: 4294967295 Expected: outputAttributes[i].value Which is: 0 /home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:154: Failure Value of: expectedDefaultResults[i] Actual: 4294967295 Expected: outputAttributes[i].value Which is: 0 /home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:152: Failure Value of: expectedDefaultResults[i] Actual: 4 Expected: outputAttributes[i].type Which is: 2 [ ] Setting/Getting atrributes [ FAILED ] the root cause is that svm work queue has not finished when svm_range_get_attr is called, thus some garbage svm interval tree data make svm_range_get_attr get wrong result. Flush work queue before iterate svm interval tree. Signed-off-by:
Yifan Zhang <yifan1.zhang@amd.com> Reviewed-by:
Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by:
-
Kenneth Feng authored
change the workload type for some cards as it is needed. Signed-off-by:
Kenneth Feng <kenneth.feng@amd.com> Reviewed-by:
Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by:
-
Kenneth Feng authored
This reverts commit 0979d432. Revert this because it does not apply to all the cards. Signed-off-by:
-
Candice Li authored
Signed-off-by:
-
Jiange Zhao authored
When guest received FLR notification from host, it would lock adapter into reset state. There will be no more job submission and hardware access after that. Then it should send a response to host that it has prepared for host reset. Signed-off-by:
Jiange Zhao <Jiange.Zhao@amd.com> Signed-off-by:
Peng Ju Zhou <PengJu.Zhou@amd.com> Reviewed-by:
Emily.Deng <Emily.Deng@amd.com> Signed-off-by:
-
Kevin Wang authored
the following clock is only support voltage DPM, change attribute to RO: 1. pp_dpm_sclk 2. pp_dpm_mclk 3. pp_dpm_fclk Signed-off-by:
Kevin Wang <kevin1.wang@amd.com> Reviewed-by:
-
Kevin Wang authored
the following message is allowed in sriov mode: 1. GetEnabledSmuFeaturesLow 2. GetEnabledSmuFeaturesHigh Signed-off-by:
-
Kevin Wang authored
v1: 1. change return value to avoid smu driver probe fails when FEATURE_PPT is not enabled. 2. if FEATURE_PPT is not enabled, set power limit value to 0. v2: instead dev_err with dev_warn Signed-off-by:
-
Kevin Wang authored
v1: 1. skip to load smu firmware in sriov mode for aldebaran chip 2. using vbios pptable if in sriov mode. v2: clean up smu driver code in sriov code path Signed-off-by:
-
Kevin Wang authored
the following feature is wrong, it will cause sysnode of pp_features show error: 1. DPM_XGMI 2. VCN_DPM Signed-off-by:
-
Jack Zhang authored
Why: Previously hw fence is alloced separately with job. It caused historical lifetime issues and corner cases. The ideal situation is to take fence to manage both job and fence's lifetime, and simplify the design of gpu-scheduler. How: We propose to embed hw_fence into amdgpu_job. 1. We cover the normal job submission by this method. 2. For ib_test, and submit without a parent job keep the legacy way to create a hw fence separately. v2: use AMDGPU_FENCE_FLAG_EMBED_IN_JOB_BIT to show that the fence is embedded in a job. v3: remove redundant variable ring in amdgpu_job v4: add tdr sequence support for this feature. Add a job_run_counter to indicate whether this job is a resubmit job. v5 add missing handling in amdgpu_fence_enable_signaling Signed-off-by:
Jingwen Chen <Jingwen.Chen2@amd.com> Signed-off-by:
Jack Zhang <Jack.Zhang7@hotmail.com> Reviewed-by:
Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed by: Monk Liu <monk.liu@amd.com> Signed-off-by:
-
- 11 Aug, 2021 6 commits
-
-
Tuo Li authored
The variable dc->clk_mgr is checked in: if (dc->clk_mgr && dc->clk_mgr->funcs->get_clock) This indicates dc->clk_mgr can be NULL. However, it is dereferenced in: if (!dc->clk_mgr->funcs->get_clock) To fix this null-pointer dereference, check dc->clk_mgr and the function pointer dc->clk_mgr->funcs->get_clock earlier, and return if one of them is NULL. Reported-by:TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by:
Tuo Li <islituo@gmail.com> Signed-off-by:
-
Tuo Li authored
gpu: drm: amd: amdgpu: amdgpu_i2c: fix possible uninitialized-variable access in amdgpu_i2c_router_select_ddc_port() The variable val is declared without initialization, and its address is passed to amdgpu_i2c_get_byte(). In this function, the value of val is accessed in: DRM_DEBUG("i2c 0x%02x 0x%02x read failed\n", addr, *val); Also, when amdgpu_i2c_get_byte() returns, val may remain uninitialized, but it is accessed in: val &= ~amdgpu_connector->router.ddc_mux_control_pin; To fix this possible uninitialized-variable access, initialize val to 0 in amdgpu_i2c_router_select_ddc_port(). Reported-by: -
Mukul Joshi authored
This patch adds support to program trap handler settings when loading driver with software scheduler (sched_policy=2). Signed-off-by:
Mukul Joshi <mukul.joshi@amd.com> Suggested-by:
Jay Cornwall <Jay.Cornwall@amd.com> Reviewed-by:
Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Signed-off-by:
-
Philip Yang authored
For xnack on, if range ACCESS or ACCESS_IN_PLACE (AIP) by single GPU, or range is ACCESS_IN_PLACE by mGPUs and all mGPUs connection on XGMI same hive, the best prefetch location is prefetch_loc GPU. Otherwise, the best prefetch location is always CPU because GPU does not have coherent mapping VRAM of other GPUs even with large-BAR PCIe connection. Signed-off-by:
Philip Yang <Philip.Yang@amd.com> Reviewed-by:
-
Ryan Taylor authored
Attempt od settings restore and disable restore flag on restore fan mode failure. v2: Update fan mode to auto and fan speed to zero (Lijo) Reviewed-by:
Ryan Taylor <Ryan.Taylor@amd.com> Signed-off-by:
-
Ryan Taylor authored
Adds missing edge case to smu_restore_dpm_user_profile. v2: Don't restore fan mode auto (Lijo) Reviewed-by:
-
- 10 Aug, 2021 8 commits
-
-
Darren Powell authored
replacing printfs with sysfs_emit === Test === AMDGPU_PCI_ADDR=`lspci -nn | grep "VGA\|Display" | cut -d " " -f 1` AMDGPU_HWMON=`ls -la /sys/class/hwmon | grep $AMDGPU_PCI_ADDR | awk '{print $9}'` HWMON_DIR=/sys/class/hwmon/${AMDGPU_HWMON} LOGFILE=pp_printf.test.log lspci -nn | grep "VGA\|Display" > $LOGFILE FILES="pwm1_enable pwm1_min pwm1_max pwm1 fan1_input fan1_target fan1_enable power1_cap_min " for f in $FILES do echo === $f === >> $LOGFILE cat $HWMON_DIR/device/$f >> $LOGFILE done cat $LOGFILE Signed-off-by:Darren Powell <darren.powell@amd.com> Reviewed-by:
-
Darren Powell authored
replacing printfs with sysfs_emit minor smu7 change to remove compiler warning comparison of int and uint32_t minor smu8 change to remove compiler warning comparison of int and uint32_t === Test === AMDGPU_PCI_ADDR=`lspci -nn | grep "VGA\|Display" | cut -d " " -f 1` AMDGPU_HWMON=`ls -la /sys/class/hwmon | grep $AMDGPU_PCI_ADDR | awk '{print $9}'` HWMON_DIR=/sys/class/hwmon/${AMDGPU_HWMON} LOGFILE=pp_printf.test.log lspci -nn | grep "VGA\|Display" > $LOGFILE FILES="pp_dpm_sclk pp_power_profile_mode " for f in $FILES do echo === $f === >> $LOGFILE cat $HWMON_DIR/device/$f >> $LOGFILE done cat $LOGFILE Signed-off-by: -
Darren Powell authored
=== Test === AMDGPU_PCI_ADDR=`lspci -nn | grep "VGA\|Display" | cut -d " " -f 1` AMDGPU_HWMON=`ls -la /sys/class/hwmon | grep $AMDGPU_PCI_ADDR | awk '{print $9}'` HWMON_DIR=/sys/class/hwmon/${AMDGPU_HWMON} LOGFILE=pp_printf.test.log lspci -nn | grep "VGA\|Display" > $LOGFILE FILES="pp_dpm_sclk pp_features pp_power_profile_mode " for f in $FILES do echo === $f === >> $LOGFILE cat $HWMON_DIR/device/$f >> $LOGFILE done cat $LOGFILE Signed-off-by: -
Darren Powell authored
initial modification of files vega10_hwmgr.c === Test === AMDGPU_PCI_ADDR=`lspci -nn | grep "VGA\|Display" | cut -d " " -f 1` AMDGPU_HWMON=`ls -la /sys/class/hwmon | grep $AMDGPU_PCI_ADDR | awk '{print $9}'` HWMON_DIR=/sys/class/hwmon/${AMDGPU_HWMON} LOGFILE=pp_printf.test.log lspci -nn | grep "VGA\|Display" > $LOGFILE FILES="pp_dpm_sclk pp_features pp_power_profile_mode " for f in $FILES do echo === $f === >> $LOGFILE cat $HWMON_DIR/device/$f >> $LOGFILE done cat $LOGFILE Signed-off-by: -
Darren Powell authored
initial modification of files renoir_ppt.c aldebaran_ppt.c yellow_carp_ppt.c === Test === AMDGPU_PCI_ADDR=`lspci -nn | grep "VGA\|Display" | cut -d " " -f 1` AMDGPU_HWMON=`ls -la /sys/class/hwmon | grep $AMDGPU_PCI_ADDR | awk '{print $9}'` HWMON_DIR=/sys/class/hwmon/${AMDGPU_HWMON} LOGFILE=pp_printf.test.log lspci -nn | grep "VGA\|Display" > $LOGFILE FILES="pp_dpm_sclk pp_power_profile_mode " for f in $FILES do echo === $f === >> $LOGFILE cat $HWMON_DIR/device/$f >> $LOGFILE done cat $LOGFILE Signed-off-by: -
Darren Powell authored
modification of smu11 files arcturus_ppt.c sienna_cichlid_ppt.c vangogh_ppt.c === Test === AMDGPU_PCI_ADDR=`lspci -nn | grep "VGA\|Display" | cut -d " " -f 1` AMDGPU_HWMON=`ls -la /sys/class/hwmon | grep $AMDGPU_PCI_ADDR | awk '{print $9}'` HWMON_DIR=/sys/class/hwmon/${AMDGPU_HWMON} LOGFILE=pp_printf.test.log lspci -nn | grep "VGA\|Display" > $LOGFILE FILES="pp_dpm_sclk pp_power_profile_mode " for f in $FILES do echo === $f === >> $LOGFILE cat $HWMON_DIR/device/$f >> $LOGFILE done cat $LOGFILE Signed-off-by: -
Darren Powell authored
initial modification of files smu_cmn.c navi10_ppt.c === Test === AMDGPU_PCI_ADDR=`lspci -nn | grep "VGA\|Display" | cut -d " " -f 1` AMDGPU_HWMON=`ls -la /sys/class/hwmon | grep $AMDGPU_PCI_ADDR | awk '{print $9}'` HWMON_DIR=/sys/class/hwmon/${AMDGPU_HWMON} LOGFILE=pp_printf.test.log lspci -nn | grep "VGA\|Display" > $LOGFILE FILES="pp_dpm_sclk pp_sclk_od pp_mclk_od pp_dpm_pcie pp_od_clk_voltage pp_power_profile_mode " for f in $FILES do echo === $f === >> $LOGFILE cat $HWMON_DIR/device/$f >> $LOGFILE done cat $LOGFILE Signed-off-by: -
Alex Deucher authored
There may be multiple instances and only one is harvested. v2: fix typo in commit message Fixes: 83a0b863 ("drm/amdgpu: add judgement when add ip blocks (v2)") Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1673Reviewed-by:
Guchun Chen <guchun.chen@amd.com> Reviewed-by:
James Zhu <James.Zhu@amd.com> Signed-off-by:
-
