Add new entry for stm32mp257f-ev1 board.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>

Three packages exist for stm32mp25 dies. As ball-out is different between
them, this patch covers those differences by introducing dedicated pinctrl
dtsi files. Each dtsi pinctrl package file describes the package ball-out
through gpio-ranges.

Available packages are:

STM32MP25xAI: 18*18/FCBGA 172 ios
STM32MP25xAK: 14*14/FCBGA 144 ios
STM32MP25xAL: 10*10/TFBGA 144 ios

It includes also the common file used for pin groups definition.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

STM32MP25 family is composed of 4 SoCs defined as following:

-STM32MP251: common part composed of 1*Cortex-A35, common peripherals like
SDMMC, UART, SPI, I2C, PCIe, USB3, parallel and DSI display, 1*ETH ...

-STM32MP253: STM32MP251 + 1*Cortex-A35 (dual CPU), a second ETH, CAN-FD and
LVDS display.

-STM32MP255: STM32MP253 + GPU/AI and video encode/decode.
-STM32MP257: STM32MP255 + ETH TSN switch (2+1 ports).

A second diversity layer exists for security features/ A35 frequency:
-STM32MP25xY, "Y" gives information:
 -Y = A means A35@1.2GHz + no cryp IP and no secure boot.
 -Y = C means A35@1.2GHz + cryp IP and secure boot.
 -Y = D means A35@1.5GHz + no cryp IP and no secure boot.
 -Y = F means A35@1.5GHz + cryp IP and secure boot.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add a dedicated ARCH_STM32 for STM32 SoCs config. First STM32 Armv8 SoC
family is the STM32MP25 which is composed of STM32MP251, STM32MP253,
STM32MP255, STM32MP257 SoCs.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add the new syscon compatible for STM32MP25 syscfg = "st,stm32mp25-syscfg".
Reorder enum following ASCII oredering.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Add stm32mp257 pinctrl support.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Add support for st,stm32mp257-pinctrl and st,stm32mp257-z-pinctrl.
Add packages AI, AK and AL (values : 0x100, 0x400 and 0x800)
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Use "dai-format" to configure DAI audio format as specified in
audio-graph-port.yaml bindings.

Fixes: 144d1ba7 ("ARM: dts: stm32: Adapt STM32MP157 DK boards to stm32 DT diversity")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The audio routing flow is not correct, the flow should be from source
(second element in the pair) to sink (first element in the pair). The
flow now is from "HP_OUT" to "Playback", where "Playback" is source
and "HP_OUT" is sink, i.e. the direction is swapped and there is no
direct link between the two either.

Fill in the correct routing, where "HP_OUT" supplies the "Headphone Jack",
"Line In Jack" supplies "LINE_IN" input, "Microphone Jack" supplies "MIC_IN"
input and "Mic Bias" supplies "Microphone Jack".

Fixes: 34e0c784 ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Correct the following warnings by adding the required supplies (AVDD, DVDD)
for the ov5640 node.

arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'AVDD-supply' is a required property
From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'DVDD-supply' is a required property
From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The generic ADC channel binding is recommended over legacy one, update the
DT to the modern binding. No functional change. For further details, see
commit which adds the generic binding to STM32 ADC binding document:
'664b9879 ("dt-bindings: iio: stm32-adc: add generic channel binding")'
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Use STM32 ADC generic bindings instead of legacy bindings on
DHCOR Testbench board.

The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Use STM32 ADC generic bindings instead of legacy bindings on
DHCOR DRC Compact board.

The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Use STM32 ADC generic bindings instead of legacy bindings on
emtrion GmbH Argon boards.

The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Use STM32 ADC generic bindings instead of legacy bindings on
STM32MP157c-ed1 board.

The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

U-Boot enables ADC1&2 to support USB power measurement and ADC
calibration on STM32MP15x Disco boards.
When leaving U-boot the ADCs do not return to power down state
to keep ADC linear calibration available for kernel.
Enable ADC1&2 by default on STM32MP15xx-DKx boards to align kernel
DT with Uboot. This avoids to shutdown the ADCs VDDA, while the
ADCs are not in power down.

Use STM32 ADC generic bindings instead of legacy bindings on
STM32MP15xx-DKx boards.

The ADC pins on Arduino connector are not set by default.
These pins are added in A7 Disco example DTs only.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Set STM32 ADC2 as a consumer of BSEC on STM32MP15, to retrieve
vrefint calibration data saved in OTP.

During the calibration process vrefp is set to 3.3V and the data
acquired is saved to the OTP. This data is used by the ADC driver
to calculated the actual value of vrefp according to the formula:
vrefp = 3.3 x vrefint_cal / vrefint_data

The vrefint channel provides the actual value of vrefp,
which can be used to correct ADC acquisition data.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Describe vrefint calibration cell to be retrieved through bsec.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add STM32 ADC2 internal channels VREFINT and VDDCORE to STM32MP15x SoCs.
VBAT internal channel is not defined by default in SoC DT, and
has be defined in board DT when needed, instead. This avoids unwanted
current consumption on battery, when ADC conversions are performed
on any other channels.

The internal channels are defined in STM32MP15 SoC DT according to the
generic IIO channel bindings. The STM32 driver does not support a mixed
use of legacy and generic channels. When generic channels are defined,
legacy channels are ignored. This involves that the board device trees
using legacy bindings for ADC2, have to be reworked.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Those concern:
  * "#size-cells" and "#address-cells" wrongly used
  * residual "reg" property appearing on endpoints where it could be
    avoided
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Fixes DSI related warnings:

 * "#size-cells" and "#address-cells" wrongly used
 * Changed 'panel-dsi@0' to 'panel@0' according to dsi-controller.yaml
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

"#address-cells" and "#size-cells" are two properties that are not
mandatory. For instance, the DSI could refer to a bridge outside the scope
of the node rather than include a 'panel@0' subnode. By doing so, address
and size fields become then unnecessary, creating a warning at build time.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Several warnings appear when building and checking stm32f429 device-tree:

arch/arm/boot/dts/stm32f469-disco.dts:182.28-184.5: Warning (unit_address_vs_reg): /soc/display-controller@40016800/port/endpoint@0: node has a unit name, but no reg or ranges property

.../arch/arm/boot/dts/stm32f469-disco.dtb: dsi@40016c00: Unevaluated properties are not allowed ('panel-dsi@0' was unexpected)
	From schema: .../Documentation/devicetree/bindings/display/st,stm32-dsi.yaml

Fix those.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Fix the following error in kernel log due to too long sound card name:
"
asoc-audio-graph-card sound: ASoC: driver name too long 'STM32MP1-AV96-HDMI' -> 'STM32MP1-AV96-H'
"

Fixes: e027da34 ("ARM: dts: stm32: Add bindings for audio on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Fixes stm32mp15*-scmi DTS files introduced in [1]:
This patch fixes the node which uses the MCU reset and adds the
missing HOLD_BOOT which is also handled by the SCMI reset service.

This change cannot be applied as a fix on commit [1], the management
of the hold boot impacts also the stm32_rproc driver.

[1] 'commit 5b7e5831 ("ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)")'
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Since the introduction of the SCMI for the management
of the MCU hold boot in OP-TEE, management of the hold boot by SMC call
is deprecated.
- Clean the st,syscfg-tz  which allows to determine if the trust
zone is enable.
- Add reset-names properties to be able to differentiate the MCU reset and
  the MCU HOLD BOOT.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add the Phytec STM32MP1-3 Dev board. The devboard uses a Phytec
stm32m157c-som.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The Phytec STM32MP1 based SoMs feature up to 1 GB DDR3LP RAM, up to 1 GB
eMMC, up to 16 MB QSPI and up to 128 GB NAND flash.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The Phytec STM32MP1 based SoMs feature up to 1 GB DDR3LP RAM, up to
1 GB eMMC, up to 16 MB QSPI and up to 128 GB NAND flash.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add a sleep mux option for the SPI1 pins_a mux.

This is used on the Phycore STM32MP1.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add idle and sleep mux option for the USART3 pins_a.

This is used on the Phycore STM32MP1.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add a mux option for the USART1 pins.

This is used on the Phycore STM32MP1.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add another option for the SDMMC_D47 pins.

This is used on the Phycore STM32MP1.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add another option for the SDMMC_B4 pins.
It is almost identical to sdmmc1_b4_pins_a but the SDMMC1_D2 pin.

This is used on the Phycore STM32MP1.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add another option for the SAI2B pins.

This is used on the Phycore STM32MP1.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Add another option for the ethernet0 pins.
It is almost identical to ethernet0_rgmii_pins_c apart from TXD0/1.

This is used on the Phycore STM32MP1.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The patch replaces the number 12 with the appropriate numerical constant
already defined in the file stm32f7-rcc.h.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

The ethernet MAC EEPROM is not populated on the SoM itself, it has to be
populated on each carrier board. Move the EEPROM into the correct place
in DTs, i.e. the carrier board DTs. Add label to the EEPROM too.

Fixes: 7e76f82a ("ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Replace deprecated st,hw-flow-ctrl with uart-has-rtscts .
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>

Remove unnecessary space in device tree stm32mp15xx-dkx.dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>