Adding support for the TC358746 parallel <-> MIPI CSI bridge. This chip
supports two operating modes:
  1st) parallel-in -> mipi-csi out
  2nd) mipi-csi in -> parallel out

This patch only adds the support for the 1st mode.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Sakari Ailus: remove() now returns void]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Add the bindings for the Toshiba TC358746 Parallel <-> MIPI-CSI bridge
driver.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

For MIPI-CSI sender use-case it is common to specify the allowed
link-frequencies which should be used for the MIPI link and is
half the hs-clock rate.

This commit adds a helper to calculate the D-PHY timing based on the
hs-clock rate so we don't need to calculate the timings within the
driver.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Factor out the calculation into phy_mipi_dphy_calc_config(). This is
needed for the follow up patch which adds the support to calculate the
timings based on a given hs clock. No functional changes are done.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Complain in the newly added s_stream video op wrapper if disabling
streaming failed. Also return zero in this case as there's nothing the
caller can do to return the error.

This way drivers also won't need to bother with printing error messages.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>

Add support for low-power probe to the driver. Also fix runtime PM API
usage in the driver.

Much of the hassle comes from different factors affecting device power
states during probe for ACPI and DT.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Fixes: 85989122 ("media: i2c: dw9768: Add DW9768 VCM driver")

The IMX290 gain register controls the analogue gain. Replace the
V4L2_CID_GAIN control with V4L2_CID_ANALOGUE_GAIN.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Implement read-only access to crop selection rectangles to expose the
analogue crop rectangle. The public (leaked) IMX290 documentation is not
very clear on how cropping is implemented and configured exactly, so
the margins may not be entirely accurate.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The driver duplicates the same pattern to access the try or active
format in multiple locations. Factor it out to a separate function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Registers 0x3012, 0x3013 and 0x3480 are not documented and are set in
the per-mode register arrays with values indentical for all modes. Move
them to the common array.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Create the V4L2_CID_ORIENTATION and V4L2_CID_ROTATION controls to
expose the corresponding fwnode properties.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Add support for the V4L2_CID_HBLANK and V4L2_CID_VBLANK controls to the
imx290 driver. Make the controls read-only to start with, to report the
values to userspace for timing calculation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The imx290_probe() function is too large. Split control initialzation to
a dedicated function to increase code readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The gain is expressed in multiple of 0.3dB, as a value between 0.0dB
and 72.0dB. Gains between 0.0dB and 30.0dB (included) apply analog gain
only, higher gains from 30.3dB to 72dB apply additional digital gain.

The maximum gain value is erroneously set to 72. Increase it to 100 to
cover the whole analog gain range. Support for digital gain can be added
separately if needed.

The IMX327 and IMX462 are largely compatible with the IMX290, but have
an analog gain range of 0.0dB to 29.4dB and 42dB of digital gain. When
support for those sensors gets added to the driver, the gain control
should be adjusted accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Support configuring the exposure time, which is expressed as the
complement of the exposure time (frame period minus integration time).
The frame period is currently fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Define macros for all registers programmed by the driver for which
documentation is available to increase readability. This starts making
use of 16-bit registers in the register arrays, so the value field has
to be increased to 32 bits.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Error handling for register writes requires checking the error status of
every single write. This makes the code complex, or incorrect when the
checks are omitted. Simplify this by passing a pointer to an error code
to the imx290_write_reg() function, which allows writing multiple
registers in a row and only checking for errors at the end.

While at it, rename imx290_write_reg() to imx290_write() as there's
nothing else than registers to write, and rename imx290_read_reg()
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Define registers with the appropriate size, using the variable-size
register access mechanism that has just been introduced. This simplifies
the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The IMX290 has registers of different sizes. To simplify the code,
handle this in the read/write functions instead of in the callers by
encoding the register size in the symbolic name macros. All registers
are defined as 8-bit for now, a subsequent change will move to larger
registers where applicable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The HMAX value specifies the total line length in pixels. It's thus more
readable in decimal than hexadecimal. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Only two registers are ever read, and once only. There's no need to
cache values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The imx290_write_buffered_reg() function wraps a register write with
register hold, to enable changing multiple registers synchronously. It
is used for the gain only, which is an 8-bit register, defeating its
purpose.

The feature is useful, but should be implemented differently. Drop the
function for now, to prepare for a rework of register access.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Use ARRAY_SIZE(imx290->supplies) for code that needs the size of the
array, instead of relying on the IMX290_NUM_SUPPLIES. The result is less
error-prone as it ties the size to the array.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Knowing why I2C transfers fail is useful for debugging. Extend the error
message to print the error code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The link frequency and pixel rate controls are set without holding the
control handler lock, resulting in kernel warnings. As the value of
those controls depend on the format, the simplest fix is to use the
device lock for the control handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Convert the Sony IMX290 DT binding from text to YAML. Add Manivannan as
a maintainer given that he is listed in MAINTAINERS for the file, as
volunteering myself.

The name of the input clock, "xclk", is wrong as the hardware manual
names it INCK. As the device has a single clock, the name could be
omitted, but that would require a corresponding change to the driver and
is thus a candidate for further patches.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The VGXY61 has a quad lanes CSI-2 output port running at 800mbps per
lane, and supports RAW8, RAW10, RAW12, RAW14 and RAW16 formats.
The driver handles both sensor types:
- VG5661 and VG6661: 1.6 Mpx (1464 x 1104) 75fps.
- VG5761 and VG6761: 2.3 Mpx (1944 x 1204) 60 fps.
The driver supports:
- HDR linearize mode, HDR substraction mode, and no HDR
- GPIOs LEDs strobing
- Digital binning and analog subsampling
- Horizontal and vertical flip
- Manual exposure
- Analog and digital gains
- Test patterns
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
[Sakari Ailus: remove() now returns void]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Document V4L2_CID_HDR_MODE possible values for this sensor.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Add device tree binding for the ST VGXY61 camera sensor, and update
MAINTAINERS file.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Add V4L2_CID_HDR_MODE as a menu item control to set the HDR mode of the
sensor, and its documentation.
Menu items are not standardized as they differ for each sensors.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

This extends the greyscale media bus family originally from
MEDIA_BUS_FMT_Y8_1X8 up to MEDIA_BUS_FMT_Y14_1X14 by adding
MEDIA_BUS_FMT_Y16_1X16, and behaves the same way with 16 bits.
Add its documentation in subdev-formats.rst
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Add a V4L2 sub-device driver for OmniVision OV4689 image sensor. This
is a 4 Mpx image sensor using the I2C bus for control and the CSI-2
bus for data.

This driver supports following features:
- manual exposure and analog gain control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
  + 2688x1520 at 30 fps

The driver provides all mandatory V4L2 controls for compatibility with
libcamera. The sensor supports 1/2/4-lane CSI-2 modes, but the driver
implements 4 lane mode only at this moment.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Add device-tree binding documentation for OV4689 image sensor driver,
and the relevant MAINTAINERS entries.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Add a V4L2 sub-device driver for Omnivision ov08X40 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.

This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
  + 3856x2464 at 30FPS
  + 1928x1208 at 30FPS
Signed-off-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Commit 1f391df4 ("media: v4l2-async: Use endpoints in
__v4l2_async_nf_add_fwnode_remote()") changed the data that is stored in
the v4l2_async_subdev internals from the fwnode pointer to the parent
device to the fwnode pointer to the matched endpoint. This broke the
sensor matching code, which relied on the particular fwnode data in the
v4l2_async_subdev internals. Fix this by simply matching the
v4l2_async_subdev pointer, which is already available there.
Reported-by: Daniel Scally <djrscally@gmail.com>
Fixes: fa91f105 ("[media] exynos4-is: Add support for asynchronous subdevices registration")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The V4L2 fwnode data structure doesn't get freed on unbind, which leads to
a memleak.

Fixes: e43ccb0a ("media: i2c: Add support for the OV5648 image sensor")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

There were no runtime PM callbacks registered, leaving regulators being
enabled while the device is suspended on DT systems. Adjust and register
existing power controlling functions to turn them off/on.
Signed-off-by: Hidenori Kobayashi <hidenorik@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

Error path seems to be swaped. Fix the order and provide some meaningful
names.

Fixes: bee3d511 ("[media] ad5820: Add driver for auto-focus coil")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

The OV5645 sensor has a single clock source, so just drop fetching the
clk reference by name.

This is in preparation to drop the "clock-names" property from the DT
binding.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

If any of the checks related to the supported link frequencies fail, then
the V4L2 fwnode resources don't get released before returning, which leads
to a memleak. Fix this by properly freeing the V4L2 fwnode data in a
designated label.

Fixes: e8c08826 ("media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>