Merge tag 'realview-dts-split' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt

Pull "RealView DTS file fixup and split" from Linus Walleij:

Fix the ethernet issue on revision D of the RealView EB
Split the DTS files in per-revision variants

* tag 'realview-dts-split' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
  ARM: dts: add RealView EB rev D A9 MPCore variant
  ARM: dts: split RealView EB 11MPCore variants
  ARM: dts: add device tree for the RealView EB Rev D
  ARM: dts: fix RealView EB SMSC ethernet version

Merge tag 'tegra-for-4.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

Pull "ARM: tegra: Device tree changes for v4.9-rc1" from Thierry Reding:

Contains a couple of cleanups for Tegra114 device trees.

* tag 'tegra-for-4.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: Correct polarity for Tegra114 PMIC interrupt
  ARM: tegra: Fix Tegra114 USB compatible values

Merge tag 'v4.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Pull "Rockchip dts32 changes for 4.9" from Heiko Stübner:

32bit Rockchip devicetree changes containing two new rk3288 boards (Fennec
and Firefly-reload), display support for the rk3288-evb, support for the
recently added firmware reboot-flag support and some housekeeping cleanups.

* tag 'v4.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: Add sensor-supplies on PopMetal-RK3288 board
  ARM: dts: rockchip: fix L3G4200D i2c address on PopMetal-RK3288 board
  ARM: dts: rockchip: enable usbotg for Popemtal-rk3288 board
  ARM: dts: rockchip: add missing regulators for firefly reload board
  ARM: dts: rockchip: remove excess sd properties from firefly reload
  ARM: dts: rockchip: add syscon-reboot-mode DT node
  soc: rockchip: add reboot-mode header
  ARM: dts: rockchip: move rk3288 usbphy under the GRF node
  ARM: dts: rockchip: add rk3288-firefly-reload
  ARM: dts: rockchip: add dts for RK3288-Fennec boards
  ARM: dts: rockchip: add the panel power supply for rk3288-evb board with rk808 pmu
  ARM: dts: rockchip: add the panel power supply for rk3288-evb board with act8846 pmu
  ARM: dts: rockchip: add eDP/panel display device nodes for rk3288-evb

Merge tag 'sunxi-dt-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt

Pull "Allwinner DT changes for 4.9" from Maxime Ripard:

Business as usual on our side, with a mix of new boards and new IPs enabled
on boards:
  - Support for the GPIO found on the AXP PMIC
  - ESP8089 on the relevant boards
  - More boards converted to the reference design and q8 designs
  - New boards: Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange
    Pi Lite, Olimex A33-Olinuxino, Empire Electronix M712, inet-d978_rev2,
    Nano Pi Neo

* tag 'sunxi-dt-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (31 commits)
  devicetree: Add vendor prefix for FriendlyARM
  ARM: dts: sun8i: Add dts file for the NanoPi NEO SBC
  ARM: dts: sun8i-q8-common: Add support for SDIO wifi controllers
  ARM: dts: sun8i: Add dts file for the Orange Pi Plus2E SBC
  ARM: dts: sun8i: Orange Pi Plus dts is for the Plus and Plus 2
  ARM: dts: sun8i: Add PWM controller node in H3
  ARM: dts: sun8i: Add dts file for inet-d978_rev2 tablets
  ARM: dts: sun9i: Add missing #interrupt-cells to R_PIO pinctrl device node
  ARM: dts: sun8i: Rename reference-design-tablet touchscreen node
  ARM: dts: sun5i: Add dts file for the Empire Electronix M712 tablet
  ARM: dts: sun5i: Convert inet-98v-rev2 dts to use reference-design-tablet.dtsi
  ARM: dts: sun4i: Disable ohci1 on ba10-tv-box
  ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2809
  ARM: dts: sun8i: Add dt node for esp8089 wifi chip on polaroid-mid2407
  ARM: dts: sun8i: add NAND controller node for A23/A33
  ARM: dts: sun6i: Add new dts file for tablets using the inet-q972 PCB
  ARM: dts: sun6i: Add sun6i-reference-design-tablet.dtsi
  ARM: dts: sun6i: colorfly-e708-q1: Remove unused mma8452_int_e708_q1 node
  ARM: dts: sun9i: Switch to the AC100 RTC clock outputs for osc32k
  ARM: dts: sun9i: cubieboard4: Add device node for AC100
  ...

Merge tag 'renesas-dt2-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.9" from Simon Horman:

Fixes (for v4.9):
* Correct PWM clock parent on r8a7794 SoC

Clean-up:
* Remove obsolete vsp1 properties from r8a779[01] SoCs

New boards:
* Add r8a7792/wheat and r7s72100/rskrza1 boards

Enablement:
* Enable LEDs, DU, SDHI on r8a7792/blanche board
* Enable MMCIF and SDHI on r8a7794/alt board
* Add SPI and VSP1 to r8a7792 SoC
* Add ethernet to r7s72100 SoC

* tag 'renesas-dt2-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (26 commits)
  ARM: dts: wheat: add support for tactile switches
  ARM: dts: wheat: add QSPI support
  ARM: dts: r8a7792: add QSPI support
  ARM: dts: r8a7792: add QSPI clock
  ARM: dts: wheat: add SDHI0 support
  ARM: dts: wheat: add CAN support
  ARM: dts: r8a7794: fix PWM clock parent
  ARM: dts: rskrza1: add ethernet DT support
  ARM: dts: r7s72100: add ethernet to device tree
  ARM: dts: r7s72100: add ethernet clock to device tree
  ARM: dts: rskrza1: initial device tree
  ARM: dts: Add RSKRZA1 DT bindings documentation
  ARM: dts: wheat: add Ethernet support
  ARM: dts: wheat: initial device tree
  ARM: dts: document Wheat board
  ARM: dts: blanche: add support for general purpose LEDs
  ARM: dts: r8a7792: add VSP1V support
  ARM: dts: r8a7792: add VSP1V clocks
  ARM: dts: blanche: add DU support
  ARM: dts: blanche: add SDHI0 support
  ...

Pull "Device Tree clean up for LPC18xx platform" from Joachim Eastwood:

* Removal of skeleton.dtsi from the common armv7-m dtsi together
  with lpc18xx and efm32 platforms.

* Fix for unit address warnings from the dtc on lpc18xx/efm32.
  That is made possible with skeleton.dtsi gone.

* tag 'lpc18xx_dts_for_4.9_part2' of https://github.com/manabian/linux-lpc:
  ARM: dts: efm32: remove skeleton.dtsi include and fix unit address warnings
  ARM: dts: lpc18xx: remove skeleton.dtsi include and fix unit address warnings
  ARM: dts: armv7-m: remove skeleton.dtsi include

Pull "mvebu dt for 4.9 (part 1)" from Gregory CLEMENT:

- update for Armada XP/38x allowing using direct access SPI
- various improvement for Armada 39x platforms
- add pinctrl information for NANd on Armada 38x
- fix the kirkwood based Openblock A6 external GPIO pins

* tag 'mvebu-dt-4.9-1' of git://git.infradead.org/linux-mvebu:
  ARM: dts: mvebu: fix reference to a390 spi controller
  ARM: dts: armada-38x: Add NAND pinctrl information
  ARM: dts: kirkwood: Fix Openblock A6 external GPIO pins
  ARM: dts: mvebu: armada-395-gp: add support for the Armada 395 GP Board
  ARM: dts: mvebu: armada-390-db: add support for the Armada 390 DB board
  ARM: dts: mvebu: armada-398-db: enable supported usb interfaces
  ARM: dts: mvebu: armada-398: update the dtsi about missing interfaces
  ARM: dts: mvebu: armada-395: add support for the Armada 395 SoC family
  ARM: dts: mvebu: armada-39x: enable rtc for all Armada-39x SoCs
  ARM: dts: mvebu: armada-39x: add missing nodes describing GPIO's
  ARM: dts: mvebu: armada-39x: enable watchdog for all Armada-39x SoCs
  ARM: dts: mvebu: armada-39x: enable the thermal sensor in Armada-39x SoCs
  ARM: dts: mvebu: armada-39x: enable PMU, CA9 SoC Controller and Coherency fabric
  ARM: dts: mvebu: armada-39x: update the SDHCI node on Armada 39x
  ARM: dts: mvebu: armada-390: add missing compatibility string and bracket
  ARM: dts: mvebu: a385-db-ap: add default partition description for NAND
  ARM: dts: mvebu: a385-db-ap: enable USB (orion-ehci) port
  ARM: dts: mvebu: armada-370-xp: Add MBus mappings for all SPI devices
  ARM: dts: mvebu: A37x/XP/38x/39x: Move SPI controller nodes into 'soc' node
  ARM: dts: mvebu: Add SPI1 pinctrl defines for Armada XP

Merge tag 'qcom-dts-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Pull "Qualcomm Device Tree Changes for v4.9" from Andy Gross:

* Rework dr_mode on APQ8064 and Nexus7
* Add MSM8974 BLSP1 UART1 port
* Add AP148 SATA mapping
* Add support for LG Nexus 5 (Hammerhead)
* Fixup MSM8660/MSM8064 SPMI/MPP IRQs
* Add Nexus7 IMEM/reboot reason
* Add Honami touchscreen support
* Add TSENS support on MSM8974, APQ8064, and APQ8084
* Add APQ8060 Dragonboard PM8058 LEDs
* Rework VPH PWR REG for MSM8974

* tag 'qcom-dts-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: msm8974: Move vreg_boost node from the honami to msm8974
  ARM: dts: qcom: msm8974: Add fixed regulator node for vph-pwr-reg
  ARM: dts: add PM8058 LEDs to the APQ8060 Dragonboard
  arm: dts: apq8084: Add thermal zones, tsens and qfprom nodes
  arm: dts: apq8064: Add thermal zones, tsens and qfprom nodes
  arm: dts: msm8974: Add thermal zones, tsens and qfprom nodes
  ARM: dts: msm8974: honami: Add touchscreen
  device-tree: nexus7: Add IMEM syscon and reboot reason support
  ARM: dts: MSM8660 remove flags from SPMI/MPP IRQs
  ARM: dts: MSM8064 remove flags from SPMI/MPP IRQs
  ARM: dts: msm8974-hammerhead: Introduce gpio-keys nodes
  ARM: dts: msm8974-hammerhead: Add regulator nodes for hammerhead
  ARM: dts: qcom: Add initial DTS for LG Nexus 5 Phone
  ipq8064: dts: force AP148 SATA port mapping
  ARM: dts: msm8974: Add nodes for blsp1_uart1 serial port
  device-tree: aqp8064.dtsi: Remove usb phy dr_mode = "host"
  device-tree: nexus7: Set phy mode to otg instead of host

As noted in commit 3ebee5a2 ("arm64: dts: kill skeleton.dtsi"),
there are a number of problems with skeleton.dtsi, and it would be
prefereable to remove it entirely. As there are a large number of
existing users, fixing these up will take a while.

This patch adds a note to arm's skeleton.dtsi noting that this is the
case, to make this more obvious and hopefully minimize new uptake of
skeleton.dtsi in the mean time.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sti-dt-for-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/dt

Pull "STi dts fixes and new STi 96board support" from Patrice Chotard:

Add thermal node for STiH407 family boards
Add specific nodes for STMicroelectronics 96Board
Add new B2260 STi board file = 96Board
Fix ahci issue on STiH407 family
Fix debugfs/pinctrl kernel warning
Update gpio-cells and gpio specifier

* tag 'sti-dt-for-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
  ARM: dts: STiH41x-b2020: Update gpio specifier
  ARM: dts: STiH418-B2199: Update gpio specifier
  ARM: dts: STiH407-pinctrl: Update gpio-cells to 2
  ARM: dts: STi: Introduce B2260 board
  ARM: dts: STiH407-family: Add ports-implemented property in sata nodes
  ARM: dts: STiH407-pinctrl: Add pinctrl_rgmii1_mdio_1 node
  ARM: dts: STiH407: Move non-removable property to board file
  ARM: dts: STiH407-pinctrl: Add i2c2_alt2_1 node
  ARM: dts: STiH410: Add thermal node
  ARM: dts: STiH407: Move pio20 node to fix kernel warning

Merge tag 'omap-for-v4.9/dt-pt1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Merge "DTS related changes for omaps for v4.9 merge window" from Tony Lindgren:

- Update elm phandle for am335x

- Fix overo NAND gpmc ranges, this has always been broken so it can
  wait for the merge window

- Fix NAND and use NAND ready pin for logicpd gpmc, this can wait too
  as it's been using the older configration since the dts got added

- A series of dtc warning fixes for unit names

- Keep dcdc3, 5 and 6 enabled during suspend on am347x boards

- Disable DDR regulator during rtc-only/poweroff mode for am437x boards

- Remove redundant regulator compatibles for am437x boards

- Increas QSPI max frequency for dra7 boards

- Enable QSPI for am57xx-idk-common

- Enable am335x-wega audio support

- Workaround for i845 for dra7

- Update binding for logicpd boards

- Add gpio-decoder nodes for am335x-icev2 board

- Add linux,pci-domain property for dra7

- Fix dra7 clock data gmac_gmii_ref_clk_div and related clock tree
  entries, these can wait for merge window as Ethernet works on dra7

- A series of changes to drop skeleton.dtsi because of dtc warnings

* tag 'omap-for-v4.9/dt-pt1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (54 commits)
  ARM: dts: dra7: Add missing unit name to memory nodes
  ARM: dts: dra62x: Add missing unit name to memory nodes
  ARM: dts: dm8168: Add missing unit name to memory nodes
  ARM: dts: dm8148: Add missing unit name to memory nodes
  ARM: dts: am572x: Add missing unit name to memory nodes
  ARM: dts: am4372: Add missing unit name to memory nodes
  ARM: dts: am3517: Add missing unit name to memory nodes
  ARM: dts: am335x: Add missing unit name to memory nodes
  ARM: dts: omap5: Add missing unit name to memory nodes
  ARM: dts: omap4: Add missing unit name to memory nodes
  ARM: dts: omap3: Add missing unit name to memory nodes
  ARM: dts: omap2: Add missing unit name to memory nodes
  ARM: dts: am4372: Remove skeleton.dtsi usage
  ARM: dts: dra7: Remove skeleton.dtsi usage
  ARM: dts: dm816x: Remove skeleton.dtsi usage
  ARM: dts: dm814x: Remove skeleton.dtsi usage
  ARM: dts: am33xx: Remove skeleton.dtsi usage
  ARM: dts: omap5: Remove skeleton.dtsi usage
  ARM: dts: omap4: Remove skeleton.dtsi usage
  ARM: dts: omap3: Remove skeleton.dtsi usage
  ...

Merge tag 'keystone_dts_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt

Merge "ARM: dts: Keystone DTS for 4.9" from Santosh Shilimkar

Add K2G nodes for GPIO, IRQ and Message Manager

* tag 'keystone_dts_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: dts: keystone-k2g: Add Message Manager node
  ARM: dts: keystone-k2g: Add DSP GPIO controller node
  ARM: dts: keystone-k2g: Add keystone IRQ controller node
  ARM: dts: keystone-k2g: Add device state controller node
  ARM: dts: keystone: specify usb mode explicitly

Merge tag 'uniphier-dt-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

Merge "UniPhier ARM SoC DT updates for v4.9" from Masahiro Yamada:

* Match DT names other projects and documents
* Switch over to PSCI
* Use clock/reset drivers
* Misc

* tag 'uniphier-dt-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  ARM: dts: uniphier: add specific compatible to SoC-Glue node
  ARM: dts: uniphier: use clock/reset controllers
  ARM: dts: uniphier: switch over to PSCI
  ARM: dts: uniphier: match DT names to other projects and documents
  ARM: dts: uniphier: remove a whitespace after tabs

Merge "Samsung DeviceTree update for v4.9" from Krzysztof Kozlowski:

1. Set chosen serial bitrate which allows proper serial output when
   bootloader does pass all the data in command line.
2. Cleanup.

* tag 'samsung-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: Use 'hpd-gpios' instead of 'hpd-gpio'
  ARM: dts: exynos: Use stdout non-deprecated property and add serial options to Odroid XU/XU3/XU4

Merge "Device Tree additions for LPC18xx platform" from Joachim Eastwood:

Small fix for the compatible string for the NXP SE97 I2C chip on the
Hitex Eval board from Guenter and a couple of additional DT properties
for the DWMAC that is need for correct operation.

* tag 'lpc18xx_dts_for_4.9' of https://github.com/manabian/linux-lpc:
  ARM: dts: lpc18xx: configure dwmac properly
  ARM: dts: lpc4350-hitex-eval: fix binding for SE97 i2c device

The irq affinity is required for pmu interrupts.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Use the cache settings that were determined to give best performance
on artpec-6 typical workloads.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Use defines from the clock binding header as clock indexes.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-dt-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Merge "Renesas ARM Based SoC DT Updates for v4.9" from Simon Horman:

* Add DU, VIN, I2C, SDHI, EtherAVB, GPIO support to r8a7792
* Enable CAN0 on r8a7792/blanche
* Enable sound on r8a7794/silk
* Correct SDHI register size on r8a7794

* tag 'renesas-dt-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (26 commits)
  ARM: dts: r8a7792: add DU support
  ARM: dts: r8a7792: add DU clocks
  ARM: dts: r8a7792: fix misindented line
  ARM: dts: silk: add sound support
  ARM: dts: r8a7794: add sound support
  ARM: dts: r8a7794: add Audio-DMAC support
  ARM: dts: r8a7794: add MSTP10 clocks
  ARM: dts: r8a7794: add MSTP5 clocks
  ARM: dts: r8a7794: add audio clocks
  ARM: dts: r8a7792: add VIN support
  ARM: dts: r8a7792: add VIN clocks
  ARM: dts: r8a7792: add I2C support
  ARM: dts: r8a7792: add I2C clocks
  ARM: dts: r8a7792: add SDHI support
  ARM: dts: r8a7792: add SD clocks
  ARM: dts: r8a7794: Correct SDHI register size
  ARM: dts: blanche: add CAN0 support
  ARM: dts: r8a7792: add CAN support
  ARM: dts: r8a7792: add CAN clocks
  ARM: dts: r8a7792: add EtherAVB support
  ...

The Cortex A9 MPCore tile can be mounted on top of the revision
D variant of the RealView EB, so create another variant of the
DTS file for this.

arm-realview-eb-a9mp = mounted on pre-revision D baseboard
arm-realview-eb-a9mp-bbrevd = mounted on the revision D baseboard
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There used to be two versions of the RealView EB 11MPCore:

- arm-realview-eb-11mp.dts: the most common variant supported by
  QEMU with the revision C core tile
- arm-realview-eb-revb.dts: for the variant with the elder revision
  B core tile.

As it turns out that there are also a few variants of the
baseboard, unrelated to the coretile, and that these can of
course be mounted on top of each other in all permutations, we
create:

- arm-realview-eb-11mp.dts: the most common variant supported by
  QEMU with the pre-revision D baseboard and the revision C core
  tile.
- arm-realview-eb-11mp-bbrevd.dts: the revision D baseboard
  with the common revision C core tile.
- arm-realview-eb-11mp-ctrevb.dts: the pre-revision D baseboard
  with the revision B core tile.
- arm-realview-eb-11mp-bbrevd-ctrevb.dts: the revision D baseboard
  with the revision B core time.

Or as a table:

           | Core tile: C               | Core tile: B
-----------+----------------------------+-----------------------------------
Baseboard: |                            |
pre-D      |arm-realvie-eb-11mp         | arm-realview-eb-11mp-ctrevb
-----------+----------------------------+-----------------------------------
Baseboard: |                            |
D          |arm-realview-eb-11mp-bbrevd | arm-realview-eb-11mp-bbrevd-ctrevb
-----------+----------------------------+-----------------------------------
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The RealView EB baseboard revision D is a special case as it appears
to be undocumented in ARM official documents, while the Linux kernel
still contains special code for handling it.

commit be4f3c86
"Add RealView/EB support for the LAN9118 Ethernet chip"
adds support for the SMSC LAN9118 chip used on the D revision of
the baseboard, but no other traces of hardware deviations for this
variant can be found.

This creates a separate top-level .dts file especially for this
board version, so that it gets registered with the right type
of ethernet controller. The ethernet controller modifications
are then put into a separate .dtsi file so it can be overlaid
on other EB variants using the revision D baseboard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The ethernet version in the earlier RealView EB variants is
LAN91C111 and not LAN9118 according to ARM DUI 0303E
"RealView Emulation Baseboard User Guide" page 3-57.

Make sure that this is used for the base variant of the board.

As the DT bindings for LAN91C111 does not specify any power
supplies, these need to be deleted from the DTS file.

Fixes: 2440d29d ("ARM: dts: realview: support all the RealView EB board variants")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add  support for the  tactile switches  SW2/3 (on the debug board) as a
virtual keyboard like it  was done with the Blanche board).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Wheat board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and MTD partitions on it.

Based  on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
  Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name

by adding proper unit addresses to the memory nodes. Also add missing
device_type to the memory node while at it.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
  Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name

by adding proper unit addresses to the memory nodes.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>

Remove skeleton.dtsi from the common ARM Cortex-M dtsi. This will allow
us to remove skeleton.dtsi on a per platform basis and get rid of the
unit address warning on the memory nodes without getting duplicate memory
nodes.

See 3ebee5a2 ("arm64: dts: kill skeleton.dtsi") for additional
reasons not to use the skeleton.dtsi.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>

Guangzhou FriendlyARM Computer Tech Co., Ltd is a Chinese ARM board vendor.
Signed-off-by: James Pettigrew <james@innovum.com.au>
Reviewed-by: Rask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The NanoPi NEO is a minimal H3 based SBC. It comes with 256/512M RAM, a
micro SD slot, 10/100Mbit ethernet and a single USB-A port.
Signed-off-by: James Pettigrew <james@innovum.com.au>
Reviewed-by: Rask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Most of the sun8i q8 boards have an SDIO wifi controller, on the
variants which use an USB wifi controller, this will result in a
couple of error msg-s in dmesg when proving the sdio bus and
an used mmc controller.

The best way to deal with wifi on this boards really is to simply
let the kernel auto-detect usb or sdio wifi controllers, so we
will just have to live with the few errors in dmesg.

This has been tested on a23 based q8 tablets with ESP8089, RTL8703AS and
RTL8189FTV wifi controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Define the generic R8A7792 part of the QSPI device node.

Based  on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the QSPI clock in the R8A7792 device tree.

Based  on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Wheat board dependent  part of  the SDHI0 (connected to the
micro-SD slot)  device node along with the necessary voltage regulator.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Wheat board dependent part of the CAN0/1 device nodes...

Based  on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When removing the non-existing thermal clock I forgot to remove its
parent from the node's "clocks" property  -- this led to a wrong PWM
clock's parent clock.

Fixes: 2a29f9d6 ("ARM: dts: r8a7794: add MSTP5 clocks")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial device tree for the RZ/A1 based development board (RSK).
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>