- 31 May, 2021 7 commits
-
-
Roja Rani Yarubandi authored
We had introduced the QUP-CORE ICC path to put proxy votes from QUP wrapper on behalf of earlycon, if other users of QUP-CORE turn off this clock before the real console is probed, unclocked access to HW was seen from earlycon. With ICC sync state support proxy votes are no longer need as ICC will ensure that the default bootloader votes are not removed until all it's consumer are probed. We can safely remove ICC path for QUP-CORE clock from QUP wrapper device. Signed-off-by:
Roja Rani Yarubandi <rojay@codeaurora.org> Signed-off-by:
Akash Asthana <akashast@codeaurora.org> Reviewed-by:
Matthias Kaehlcke <mka@chromium.org> Link: https://lore.kernel.org/r/20210324101836.25272-3-rojay@codeaurora.orgSigned-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org>
-
Vinod Koul authored
Some node unit addresses were put wrongly in the dts, resulting in below warning when run with W=1 arch/arm64/boot/dts/qcom/sm8350.dtsi:693.34-702.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c222000: simple-bus unit address format error, expected "c263000" arch/arm64/boot/dts/qcom/sm8350.dtsi:704.34-713.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c223000: simple-bus unit address format error, expected "c265000" arch/arm64/boot/dts/qcom/sm8350.dtsi:1180.32-1185.5: Warning (simple_bus_reg): /soc@0/interconnect@90e0000: simple-bus unit address format error, expected "90c0000" Fix by correcting to the correct address as given in reg node Reviewed-by:
Robert Foss <robert.foss@linaro.org> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20210513060733.382420-1-vkoul@kernel.orgSigned-off-by:
-
Vinod Koul authored
Add interconnect enums instead of numbers now that interconnect is in mainline. Reviewed-by:
Bhupesh Sharma <bhupesh.sharma@linaro.org> Signed-off-by:
-
Felipe Balbi authored
With this patch, DMA has a chance of probing and doing something useful. Reviewed-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by:
Felipe Balbi <felipe.balbi@microsoft.com> Link: https://lore.kernel.org/r/20210417061951.2105530-3-balbi@kernel.orgSigned-off-by:
-
Vincent Knecht authored
Enable the MStar msg2638 touchscreen. Reviewed-by:
Stephan Gerhold <stephan@gerhold.net> Signed-off-by:
Vincent Knecht <vincent.knecht@mailoo.org> Link: https://lore.kernel.org/r/20210528114345.543761-1-vincent.knecht@mailoo.orgSigned-off-by:
-
Loic Poulain authored
The speedbin value blown in the efuse is used to determine is used to determine the voltage and frequency value for different IPs, including GPU, CPUs... So it's really not a gpu specific information. This patch simply renames 'gpu_speed_bin' node to 'speedbin'. Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
-
Robert Marko authored
One of the QUSB USB PHY-s has been left enabled by default, this is probably just a mistake as other USB PHY-s are disabled by default. It makes no sense to have it enabled by default as not all board implement USB ports, so disable it. Reviewed-by:
Kathiravan T <kathirav@codeaurora.org> Signed-off-by:
Robert Marko <robimarko@gmail.com> Link: https://lore.kernel.org/r/20210526150125.1816335-1-robimarko@gmail.comSigned-off-by:
-
- 26 May, 2021 33 commits
-
-
Konrad Dybcio authored
Add BAM DMA nodes and add required properties to devices to enable DMA operations. Signed-off-by:
-
Konrad Dybcio authored
As the name implies, the USB2 controller should only operate at USB2 speeds. Make sure it does just that by pinning it to USB High-Speed (USB2) mode. Signed-off-by:
-
satya priya authored
Add channel nodes for the on die temperatures of PMICS pmk8350, pm8350, pmr735a and pmr735b. Signed-off-by:
satya priya <skakit@codeaurora.org> Reviewed-by:
-
satya priya authored
The sc7280-idp has four PMICs, include their .dtsi files. Reviewed-by:
-
satya priya authored
Add gpio ranges and correct the compatible to add "qcom,spmi-gpio" as this pmic is on spmi bus. Reviewed-by:
-
satya priya authored
Add PON, RTC, VADC and ACD_TM support for PMK8350. Signed-off-by:
-
satya priya authored
Add gpio ranges and correct the compatible to add "qcom,spmi-gpio" as this pmic is on spmi bus. Reviewed-by:
-
satya priya authored
Add temp-alarm support for PMR735A pmic. Signed-off-by:
-
satya priya authored
Add gpio ranges and correct the compatible to add "qcom,spmi-gpio" as this pmic is on spmi bus. Reviewed-by:
-
satya priya authored
Add temp-alarm support for PM8350C pmic. Signed-off-by:
-
satya priya authored
Add base DTS file for pm7325 along with GPIOs and temp-alarm nodes. Signed-off-by:
-
satya priya authored
Add label "thermal_zones" for thermal-zones node. Signed-off-by:
-
Rajeshwari Ravindra Kamble authored
Adding thermal zone and cooling maps support in SC7280. Reviewed-by:
Rajeshwari Ravindra Kamble <rkambl@codeaurora.org> Link: https://lore.kernel.org/r/1620367641-23383-4-git-send-email-rkambl@codeaurora.orgSigned-off-by:
-
Rajeshwari Ravindra Kamble authored
Adding device node for TSENS controller and critical interrupt support in SC7280. Signed-off-by:
-
Yassine Oudjana authored
Add hs_phy_irq and ss_phy_irq to usb3. Tested-by:
Yassine Oudjana <y.oudjana@protonmail.com> Link: https://lore.kernel.org/r/dvfyYKA9vnJdunbQ1CL-dgjXtv_1wYpRnezdc3PHoCyrgmfi5KP0Dn4MtaumQEpHIQAHL9tTdqcaCK7YJWyrdWXCrPeGd4uMh-nFeu7xQYw=@protonmail.comSigned-off-by:
-
Konrad Dybcio authored
Fix the indentation, add pinctrl and move status="disabled" down. Signed-off-by:
-
Konrad Dybcio authored
Add and configure WLED node to enable backlight control on WLED-enabled devices. Signed-off-by:
-
Konrad Dybcio authored
Add required nodes to support DSI displays connected to the primary interface. Signed-off-by:
-
Konrad Dybcio authored
Add a RESIN node to support RESIN-connected buttons on some devices. Signed-off-by:
-
Konrad Dybcio authored
Disable Venus by default to allow booting without closed firmware and enable it on the boards that didn't previously disable it. This commit brings no functional difference. Signed-off-by:
-
Konrad Dybcio authored
Disable them by default to allow for booting without a display and proprietary firmware. Then, enable them on boards that didn't previously disable them. Hence, this commit brings no functional difference. Signed-off-by:
-
Konrad Dybcio authored
Add the fifth and sixth I2C host on the second BLSP, used for various board-specific peripherals. Signed-off-by:
-
Konrad Dybcio authored
Add SDHCI1 device to allow for usage of (more often than not) eMMC. Signed-off-by:
-
Konrad Dybcio authored
Set the tcsr_mutex_regs size to 0x40000 to allow for accessing all required registers that will be needed to support modem. Signed-off-by:
-
Konrad Dybcio authored
QUP and UART names start from 1. There are 6 QUPs and 2 UARTs per BLSP. Let's not further confuse programmers by stating otherwise. Signed-off-by:
-
Konrad Dybcio authored
In order to prepare for feature development, the DTs have to be workable with.. To achieve that: - Rename msmgpio to tlmm (consistency with newer DTs) - Rid msm8996-pins.dtsi and add the contents to msm8996.dtsi - Modernize the pin nodes, make them more concise - Add generic pin configuration for some hardware - Fix up some names in preparation for BLSP/UART name cleaning.. Signed-off-by:
-
Gokul Sriram Palanisamy authored
Add initial support for IPQ8074 SoC based HK10-C1 and HK10-C2 evaluation boards. Signed-off-by:
Gokul Sriram Palanisamy <gokulsri@codeaurora.org> Link: https://lore.kernel.org/r/1614328110-28866-2-git-send-email-gokulsri@codeaurora.orgSigned-off-by:
-
Yassine Oudjana authored
Disable ADSP by default and enable it in devices that use it. Also add CX power domain. Signed-off-by:
-
Sergey Senozhatsky authored
qcom camera driver allocates the ICP firmware memory dynamically, so the carveout region is unnecessary. Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Signed-off-by:
Sergey Senozhatsky <senozhatsky@chromium.org> Link: https://lore.kernel.org/r/20210525133242.188603-1-senozhatsky@chromium.orgSigned-off-by:
-
Joel Selvaraj authored
This patch adds audio support for Xiaomi Poco F1 phone. Phone's primary Mic and 3.5mm Headphone jack are handled through the SDM845 sound card and WCD9340 codec. Tested-by:
Amit Pundir <amit.pundir@linaro.org> Reviewed-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by:
Joel Selvaraj <jo@jsfamily.in> Link: https://lore.kernel.org/r/BN6PR2001MB17966ED1D787FA3F4B90A1A7D95B9@BN6PR2001MB1796.namprd20.prod.outlook.comSigned-off-by:
-
Caleb Connolly authored
Enable the ipa node so that we can bring up mobile data. Signed-off-by:
Caleb Connolly <caleb@connolly.tech> Link: https://lore.kernel.org/r/20210502014146.85642-5-caleb@connolly.techSigned-off-by:
-
Caleb Connolly authored
The rmtfs_mem region is a weird one, downstream allocates it dynamically, and supports a "qcom,guard-memory" property which when set will reserve 4k above and below the rmtfs memory. A common from qcom 4.9 kernel msm_sharedmem driver: /* * If guard_memory is set, then the shared memory region * will be guarded by SZ_4K at the start and at the end. * This is needed to overcome the XPU limitation on few * MSM HW, so as to make this memory not contiguous with * other allocations that may possibly happen from other * clients in the system. */ When the kernel tries to touch memory that is too close the rmtfs region it may cause an XPU violation. Such is the case on the OnePlus 6 where random crashes would occur usually after boot. Reserve 4k above and below the rmtfs_mem to avoid hitting these XPU Violations. This doesn't entirely solve the random crashes on the OnePlus 6/6T but it does seem to prevent the ones which happen shortly after modem bringup. Fixes: 288ef8a4 ("arm64: dts: sdm845: add oneplus6/6t devices") Signed-off-by:
-
Harigovindan P authored
Add nodes for IDP display. The display is Visionox RM69299. Signed-off-by:
Harigovindan P <harigovi@codeaurora.org> Link: https://lore.kernel.org/r/20200629135144.8265-1-harigovi@codeaurora.orgSigned-off-by:
-
