We don't expect the (hardware) cnvst trigger to be enabled at boot time,
this is a user choice made in sysfs and there is a dedicated callback to
enable/disable this trigger. Hence, we can just ensure it is disabled in
the probe at initialization time and then assume that whenever a
->read_raw() call happens, the trigger has been disabled and conversions
will start on register write.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-9-miquel.raynal@bootlin.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The call to max1027_enable_trigger() is the same in both cases thanks to
the 'state' variable, so factorize a little bit to simplify the code and
explain why we call this helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-8-miquel.raynal@bootlin.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

There are two ways to physically trigger a conversion:
- A falling edge on the cnvst pin
- A write operation on the conversion register

Let's create a helper for this.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-7-miquel.raynal@bootlin.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Make it clear that the *_set_trigger_state() hook is responsible for
cnvst based conversions by renaming the helper. This may avoid
confusions with software trigger support that is going to be
introduced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-6-miquel.raynal@bootlin.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Provide a list of ->available_scan_masks which match the device's
capabilities. Basically, these devices are able to scan from 0 to N, N
being the highest voltage channel requested by the user. The temperature
can be included or not, but cannot be retrieved alone.

The consequence is, instead of reading and pushing to the IIO buffers
all channels each time, the "minimum" number of channels will be scanned
and pushed based on the ->active_scan_mask.

For example, if the user wants channels 1, 4 and 5, all channels from
0 to 5 will be scanned and pushed to the IIO buffers. The core will then
filter out the unneeded samples based on the ->active_scan_mask that has
been selected and only channels 1, 4 and 5 will be available to the user
in the shared buffer.

Provide a comment in the code explaining this logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-5-miquel.raynal@bootlin.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

These two debug messages bring absolutely no value, let's drop them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-4-miquel.raynal@bootlin.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Memory allocation errors automatically trigger the right logs, no need
to have our own.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-3-miquel.raynal@bootlin.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Follow checkpatch.pl's main advices before hacking into the driver, mainly:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer 'unsigned int *' to bare use of 'unsigned *'
CHECK: Comparison to NULL could be written "!foo"
CHECK: Alignment should match open parenthesis
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-2-miquel.raynal@bootlin.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The NXP i.MX 8QuadXPlus SOC has a new ADC IP. After adding
the driver support for it, I add the driver info of the
NXP IMX8QXP ADC to MAINTAINERS file.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210925020555.129-4-caihuoqing@baidu.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The NXP i.MX 8QuadXPlus SOC a new ADC IP, so add
binding documentation for NXP IMX8QXP ADC.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210925020555.129-3-caihuoqing@baidu.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add
driver support for this ADC.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210925020555.129-2-caihuoqing@baidu.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This adds ways for the SoC to wake from accelerometer wake events.

In the suspend function we skip disabling the sensor if wakeup-source
and events are activated.

If buffered reads are enabled they will be deactivated before suspend.
As the onboard buffer is only holding up to 32 12-bit X/Y/Z data
triplets.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210920114221.1595543-2-sean@geanix.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add event channels that control the creation of motion events.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20210920114221.1595543-1-sean@geanix.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The ADC controller has a trimming register for fine-tune the reference
voltage. The trimming value comes from the OTP register which will be
written during chip production. This patch will read this OTP value and
configure it to the ADC register when the ADC controller probes and using
dts property "aspeed,trim-data-valid" to determine whether to execute this
flow.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-12-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

In ast2600, ADC integrate dividing circuit at last input channel for
battery sensing. This patch use the dts property "battery-sensing" to
enable this feature makes the last channel of each adc can tolerance
higher voltage than reference voltage. The offset interface of ch7 will
be separated when enabling the battery sensing mode.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-11-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch adds a compensation phase to improve the accuracy of ADC
measurement. This is the built-in function through input half of the
reference voltage to get the ADC offset.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-10-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add the function to set the sampling rate and keep the sampling period
for a driver used to wait the fresh value.
In addition, since the ADC clock is required when initializing the ADC
device, move clk_prepare_enable ahead of the initialization phase.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-9-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The ADC clock formula is
ast2400/2500:
ADC clock period = PCLK * 2 * (ADC0C[31:17] + 1) * (ADC0C[9:0] + 1)
ast2600:
ADC clock period = PCLK * 2 * (ADC0C[15:0] + 1)
They all have one fixed divided 2 and the legacy driver didn't handle it.
This patch register the fixed factory clock device as the parent of ADC
clock scaler to fix this issue.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-8-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Make driver to support ast2600 adc device.
- Use shared reset controller
- Complete the vref configure function
- Add the model data for ast2600 adc
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-7-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch use devm_add_action_or_reset to handle the error in probe
phase.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-6-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch uses need_prescaler and scaler_bit_width to set the ADC clock
scaler.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-5-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add the function to check the vref_fixed_mv and set the value to driver
data.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-4-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch refactors the model data structure to distinguish the
function form different versions of aspeed ADC.
- Rename the vref_voltage to vref_fixed_mv and add vref_mv driver data
When driver probe will check vref_fixed_mv value and store it to vref_mv
which isn't const value.
- Add num_channels
Make num_channles of iio device can be changed by different model_data
- Add need_prescaler flag and scaler_bit_width
The need_prescaler flag is used to tell the driver the clock divider needs
another Prescaler and the scaler_bit_width to set the clock divider
bitfield width.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-3-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Keep the model data pointer to driver data for reducing the usage of
of_device_get_match_data().
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-2-billy_tsai@aspeedtech.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Document the 'in_concentration_co2_scale' standard IIO attribute.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Link: https://lore.kernel.org/r/20210920135413.140310-5-jacopo+renesas@jmondi.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add support for the Senseair Sunrise 006-0-0007 driver through the
IIO subsystem.

Datasheet: https://rmtplusstoragesenseair.blob.core.windows.net/docs/Dev/publicerat/TDE5531.pdfSigned-off-by: Jacopo Mondi <jacopo@jmondi.org>
Link: https://lore.kernel.org/r/20210920135413.140310-4-jacopo+renesas@jmondi.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add documentation for the sysfs attributes of the sunrise_co2 driver.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Link: https://lore.kernel.org/r/20210920135413.140310-3-jacopo+renesas@jmondi.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add documentation for the Senseair Sunrise 006-0-0007 CO2 NDIR sensor.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920135413.140310-2-jacopo+renesas@jmondi.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Driver and device-tree also use vid-supply regulator.

Fixes: 7e000fbf ("dt-bindings: iio: magnetometer: ak8975: convert format to yaml, add maintainer")
Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210913181949.83179-1-david@ixit.czSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Device has interrupts support, which description was missing in the bindings.
Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210919203656.119742-1-david@ixit.czSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210924133515.112357-1-krzysztof.kozlowski@canonical.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105631.1474-1-caihuoqing@baidu.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105638.1525-1-caihuoqing@baidu.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

When building kernels without ACPI support the table is declared
but is not used because ACPI_PTR() turns it into a NULL.

Add the __maybe_unused attribute to stop the compiler whining.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20210919072616.3849723-1-daniel@0x0f.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This is a simple conversion. Both iio_device_register() and
iio_triggered_buffer_setup() functions have device-managed variants.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913120002.306280-1-aardelean@deviqon.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

There is nothing else that needs to be done for this driver. The remove
hook calls only the iio_device_unregister() hook.

So this driver can use devm_iio_device_register() directly.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115308.301877-1-aardelean@deviqon.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This change converts the probe of the AD5064 driver to use only
device-managed functions.

The regulator_bulk_disable() is passed on a devm_add_action_or_reset() hook
and the devm_iio_device_register() can be used to register the IIO device.

The driver has both I2C and SPI hooks inside, so all these can be removed.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115237.301310-1-aardelean@deviqon.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This change does a conversion of the driver to use device-managed init
functions. The 2 regulators and the clock inits are converted to use
devm_add_action_or_reset() callbacks for de-initializing them when the
driver unloads.

And finally the devm_iio_device_register() function can be use to register
the device.

The remove hook can finally be removed and the spi_set_drvdata() call can
also be removed as the private data is no longer used.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115209.300665-1-aardelean@deviqon.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

For this conversion, the regulators need to have some cleanup hooks
registered with devm_add_action_or_reset() and then the
devm_io_device_register() call can be used.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115121.300082-1-aardelean@deviqon.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

When building kernels without ACPI support the table is declared
but is not used because ACPI_PTR() turns it into a NULL.

Add the __maybe_unused attribute to stop the compiler whining.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20210913112913.2148026-1-daniel@0x0f.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>