- 08 Mar, 2020 40 commits
-
-
Alexandru Tachici authored
Adding dt-bindings documentation for AD5770R DAC. Signed-off-by:
Mircea Caprioru <mircea.caprioru@analog.com> Signed-off-by:
Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Alexandru Tachici authored
The AD5770R is a 6-channel, 14-bit resolution, low noise, programmable current output digital-to-analog converter (DAC) for photonics control applications. It contains five 14-bit resolution current sourcing DAC channels and one 14-bit resolution current sourcing/sinking DAC channel. Signed-off-by:
-
Gregor Riepl authored
The look-up-table for currens to lux is simply specifying all currents from 5..47 mA, if we add some values for 0..5 we can just select the index for the lux value in an array from the mA value. Use clamp() to get the value in the range of values in the array. Cc: Jonathan Bakker <xc-racer2@live.ca> Signed-off-by:
Gregor Riepl <onitake@gmail.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Daniel Junho authored
This patch add device tree binding documentation for AD7923 adc in YAML format. Signed-off-by:
Daniel Junho <djunho@gmail.com> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Matt Ranostay authored
Since Atlas Scientific device support only varies from the compatible string is ideal all the respective docs are merged into a single doc named atlas,sensor.yaml Reviewed-by:
Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by:
-
Matt Ranostay authored
Atlas Scientific DO-SM OEM sensor reads disolved oxygen in a solution. This is reported back as mg/L which maps directly to ppm and so the IIO_CONCENTRATION channel type can be used. Signed-off-by:
-
Matt Ranostay authored
Sensors don't actually need a interrupt line to give valid readings, and can triggered with CONFIG_IIO_HRTIMER_TRIGGER as well. Remove the required check for interrupt, and continue along in the probe function. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Temperature sensor works correctly only when accel and/or gyro is turned on. Prevent polling value if they are not running. Anyway it doesn't make sense to use it without sensor engines on. Signed-off-by:
Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Use runtime power management for handling chip power and sensor engines on/off. Simplifies things a lot since pm runtime already has reference counter. Usage of autosuspend reduces the number of power on/off. This makes polling interface now usable to get data at low frequency. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Sampling rate can be changed while the chip is running. It can be useful thus do not prevent it. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Rework fifo enable/disable in a separate function. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
When reading data with the polling interface, we need to wait at 1 sampling period to have a sample. For gyroscope and magnetometer, we need to wait for 2 periods before having a correct sample. Not suitable for stable or backporting. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Rewrite clock management to use automatic clock switching present since MPU6500. Sensors engine management can now turn on or off a batch of sensors which simplifies usage a lot. Temperature sensor is now turned on/off depending on usage. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Turning vdd regulator on requires a consequent sleep for the chip to power on correctly. Turning vddio regulator is much faster. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Old chips using spi require for a full reset to manually reset all signal path. This does not harm when using i2c so do it inconditionally. Exclude i2c only chips. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Init chip_config early and use its values for initial setup. More coherent, prevent possible mistakes. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Do not change the sampling rate value. Let userspace decide what is the sampling rate to use. Read only the requested axis. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
This way there is no need anymore to export the power function to i2c and spi modules. Bus setup is done inside init when power is on and the result is now checked. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
If we are here it means we have fifo enabled for 1 sensor at least. And interrupt is always required for using trigger. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
i2c auxiliary mux is done by analog switches. You do not need to set them for every i2c transfer. Just set i2c bypass bit at init and do noting in i2c de/select. Signed-off-by:
-
Jonathan Cameron authored
Split the binding in two to reflect the threshold monitor capabilities and hence interrupts vs the more straight forward parts that don't have this facility. Signed-off-by:
-
Fabrice Gasnier authored
Clock should be enabled as soon as using master modes, even before enabling timer. Or, this may provoke bad behavior on the other end (slave timer). Then, introduce 'clk_enabled' flag, instead of relying on CR1 EN bit, to keep track of clock being enabled (balanced refcount). Propagate this anywhere else in the driver. Also add 'remove' routine to stop timer and disable clock in case it has been left enabled. Enforce the user interface has been unregistered in the remove routine, before disabling the hardware to avoid possible race. So, remove use of devm_ variant to register triggers and unregister them before the hardware gets disabled [1]. [1] https://patchwork.kernel.org/patch/9956247/Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by:
-
David Heidelberg authored
- allow autoloading when build as module and defined inside DT Signed-off-by:
David Heidelberg <david@ixit.cz> Signed-off-by:
-
David Heidelberg authored
Use devm_add_action_or_reset to automatically disable the device and allow you to get rid of the remove function entirely. Signed-off-by:
-
David Heidelberg authored
AL3320a is fairly simple chip, so for suspend is enough to disable and later enable it again. Signed-off-by:
-
David Heidelberg authored
Based on: - 3320A in-kernel driver - https://www.spinics.net/lists/linux-iio/msg25145.html - https://lore.kernel.org/patchwork/patch/684179/ I decided to keep it aside of AL3320A due to different approach and much simpler design of 3010. Tested on Nexus 7 2012 (grouper/tilapia). Tested-by:
Dmitry Osipenko <digetx@gmail.com> Tested-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by:
-
David Heidelberg authored
- modified to be in part with al3010 driver - cleanup using bitfield, no functionality change intended Signed-off-by:
-
David Heidelberg authored
The Dyna-Image AL3010 is a 16-bit digital ambient light sensor which provides a multiple gain function with linear response over a dynamic range 1216/4863/19452/77806. Signed-off-by:
-
David Heidelberg authored
This commit add dt-bindings support to al3320a driver and vendor-prefix dynaimage. Partly based on unmerged commit: "iio: Add Dyna-Image AP3223 ambient light and proximity driver" Signed-off-by:
-
Alexandru Tachici authored
Move ad7192 ADC driver out of staging into mainline. Signed-off-by:
-
Alexandru Tachici authored
Updated mainline documentation on ad7192 userspace sysfs. Signed-off-by:
-
Alexandru Tachici authored
This patch removes spi_device_id table and moves the init data (id of the chip) in the .data field of of_device_id table. Signed-off-by:
-
Alexandru Tachici authored
This patch changes the static const struct iio_chan_spec arrays in a way that all the necessary attributes are set at compile time. Now ad7192_channels_config only makes the channels attribute of iio_dev point to the right array depending on the chip. Signed-off-by:
-
Alexandru Tachici authored
This patch makes the ad7192_probe fail in case regulator_get_voltage will return an error or voltage is set to 0. Signed-off-by:
-
Mircea Caprioru authored
This patch adds the posibility do read and write registers from userspace using the kernel debug direct register access option. Signed-off-by:
-
Nuno Sá authored
All of the actions done in `adis16460_initial_setup()` are now done in `__adis_initial_startup()` so, there's no need for code duplication. Signed-off-by:
Nuno Sá <nuno.sa@analog.com> Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by:
-
Nuno Sá authored
All actions done in `adis16480_initial_setup()` are now done in `__adis_initial_startup()` so, there's no need for code duplication. Furthermore, the call to `adis16480_initial_setup()` is done before any device configuration since the device will be reset if not already (via rst pin). This is actually fixing a potential bug since `adis_reset()` was being called after configuring the device which is obviously a problem. Signed-off-by:
-
Alexandru Ardelean authored
Each driver/chip that wants to validate it's product id, can now specify a 'prod_id_reg' and an expected 'prod_id' value. The 'prod_id' value is intentionally left 0 (uninitialized). There aren't (yet) any product IDs with value 0; this enforces that both 'prod_id_reg' and 'prod_id' are specified. At the very least, this routine validates that the SPI connection to the ADIS chip[s] works well. Signed-off-by:
-
Nuno Sá authored
All the ADIS devices perform, at the beginning, a self test to make sure the device is in a sane state. Previously, the logic was that the self-test was performed in adis_initial_startup() and if that failed a reset was done and then a self-test was attempted again. This change unifies the reset mechanism under the adis_initial_startup() call. A HW reset will be done if GPIO is configured, or a SW reset otherwise. This should make sure that the chip is in a sane state for self-test. Once the reset is done, the self-test operation will be performed. If anything goes wrong with self-test, the driver should just bail/error-out (i.e. no second attempt). The chip would likely not be a in a sane state state if the self-test fails after a reset. Signed-off-by:
-
Nuno Sá authored
This patch adds a dedicated self_test_reg variable. This is also a step to let new drivers make use of `adis_initial_startup()`. Some devices use MSG_CTRL reg to request a self_test command while others use the GLOB_CMD register. Signed-off-by:
-
