PHY model is being used on omap5 platforms even if port mode
is not OMAP_EHCI_PORT_MODE_PHY. So don't guess if PHY is required
or not based on PHY mode.

If PHY is provided in device tree, it must be required. So, if
devm_usb_get_phy_by_phandle() gives us an error code other
than -ENODEV (no PHY) then error out.

This fixes USB Ethernet on omap5-uevm if PHY happens to
probe after EHCI thus causing a -EPROBE_DEFER.

Cc: Johan Hovold <johan@kernel.org>
Cc: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

That makes the USB role switch support option visible and
selectable for the user. The class driver is also moved to
drivers/usb/roles/ directory.

This will fix an issue that we have with the Intel USB role
switch driver on systems that don't have USB Type-C connectors:

Intel USB role switch driver depends on the USB role switch
class as it should, but since there was no way for the user
to enable the USB role switch class, there was also no way
to select that driver. USB Type-C drivers select the USB
role switch class which makes the Intel USB role switch
driver available and therefore hides the problem.

So in practice Intel USB role switch driver was depending on
USB Type-C drivers.

Fixes: f6fb9ec0 ("usb: roles: Add Intel xHCI USB role switch driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next

Peter writes:

- Improve the over-current handling for imx
- Add the HSIC support for imx

* tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
  usb: chipidea: imx: allow to configure oc polarity on i.MX25
  usb: chipidea: imx: Warn if oc polarity isn't specified
  usb: chipidea: imx: support configuring for active low oc signal
  doc: usb: ci-hdrc-usb2: Add pinctrl properties for HSIC pin groups
  usb: chipidea: host: override ehci->hub_control
  usb: chipidea: imx: add HSIC support
  usb: chipidea: add flag for imx hsic implementation

Without CONFIG_PM, we get a new build warning here:

drivers/usb/renesas_usbhs/common.c:860:12: error: 'usbhsc_resume' defined but not used [-Werror=unused-function]
 static int usbhsc_resume(struct device *dev)
            ^~~~~~~~~~~~~
drivers/usb/renesas_usbhs/common.c:844:12: error: 'usbhsc_suspend' defined but not used [-Werror=unused-function]
 static int usbhsc_suspend(struct device *dev)
            ^~~~~~~~~~~~~~

Fixes: d54d334e ("usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

register_root_hub() calls memset() setting usb_dev->bus->devmap.
devicemap to 0 during hcd probe function (usb_hcd_pci_probe). But
in previous function which is also the procedure of usb_hcd_pci_probe(),
usb_bus_init() already initialized bus->devmap calling memset().
Furthermore, register_root_hub() is called only once in kernel.
So, calling memset() which resets usb_bus->devmap.devicemap in
register_root_hub() is redundant.
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Felipe writes:

USB changes for v4.21

So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.

There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.

Apart from these, we have the usual set of non-critical fixes and new
features all over the place.

* tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (56 commits)
  usb: dwc2: Fix disable all EP's on disconnect
  usb: dwc3: gadget: Disable CSP for stream OUT ep
  usb: dwc2: disable power_down on Amlogic devices
  Revert "usb: dwc3: pci: Use devm functions to get the phy GPIOs"
  USB: gadget: udc: s3c2410_udc: convert to DEFINE_SHOW_ATTRIBUTE
  usb: mtu3: fix dbginfo in qmu_tx_zlp_error_handler
  usb: dwc3: trace: add missing break statement to make compiler happy
  usb: dwc3: gadget: Report isoc transfer frame number
  usb: gadget: Introduce frame_number to usb_request
  usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro
  usb: renesas_usbhs: Remove dummy runtime PM callbacks
  usb: dwc2: host: use hrtimer for NAK retries
  usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS mode
  usb: mtu3: enable SETUPENDISR interrupt
  usb: mtu3: fix the issue about SetFeature(U1/U2_Enable)
  usb: mtu3: enable hardware remote wakeup from L1 automatically
  usb: mtu3: remove QMU checksum
  usb/mtu3: power down device ip at setup
  usb: dwc2: Disable power down feature on Samsung SoCs
  usb: dwc3: Correct the logic for checking TRB full in __dwc3_prepare_one_trb()
  ...

Merge tag 'phy-for-4.21_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.21

 *) Change phy set_mode ops to take both mode and setmode as arguments
 *) Add phy_configure() and phy_validate() API's mostly used for MIPI D-PHY
 *) Add helpers to get default values of parameters define in MIPI D-PHY spec
 *) Add driver for TI's CPSW Port PHY Interface Mode selection
 *) Add driver for Cadence Sierra PHY used with USB and PCIe
 *) Add driver for Freescale i.MX8MQ USB3 PHY
 *) Fixes QMP PHY bindings to allow the clocks provided by the PHY to be
    pointed at in device tree
 *) Fix for using fully specified regions (in device tree) for configuring
    the second lane in dual lane PHYs in QMP PHY
 *) Add support for Allwinner H6 USB2 PHY in phy-sun4i-usb driver
 *) Update phy-rcar-gen3-usb driver to follow the hardware manual
 *) Add support for fine grained power management in mapphone-mdm6600 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

* tag 'phy-for-4.21_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (30 commits)
  phy: qcom-qmp: Expose provided clocks to DT
  dt-bindings: phy-qcom-qmp: Move #clock-cells to child
  phy: qcom-qmp: Utilize fully-specified DT registers
  dt-bindings: phy-qcom-qmp: Fix register underspecification
  phy: ti: fix semicolon.cocci warnings
  phy: dphy: Add configuration helpers
  phy: Add MIPI D-PHY configuration options
  phy: Add configuration interface
  phy: Add MIPI D-PHY mode
  phy: add driver for Freescale i.MX8MQ USB3 PHY
  dt-bindings: phy: add binding for Freescale i.MX8MQ USB3 PHY
  phy: Use of_node_name_eq for node name comparisons
  net: ethernet: ti: cpsw: add support for port interface mode selection phy
  dt-bindings: net: ti: cpsw: switch to use phy-gmii-sel phy
  phy: ti: introduce phy-gmii-sel driver
  dt-bindings: phy: add cpsw port interface mode selection phy bindings
  phy: mvebu-cp110-comphy: fix spelling in structure name
  phy: mapphone-mdm6600: Improve phy related runtime PM calls
  phy: renesas: rcar-gen3-usb2: follow the hardware manual procedure
  phy: cadence: Add driver for Sierra PHY
  ...

Register a simple clock provider for the PHY pipe clock sources so that
device tree users can point at these clocks via phandles to the lane
nodes.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The phy-qcom-qmp bindings specified #clock-cells as 1. This was never used
because of_clk_add_provider() was never called, so there was no way anybody
could reference these clocks from DT. Furthermore, even if they could be
accessed, the bindings never specified what should go in that additional
cell.

Fix these incomplete and broken bindings. Move the #clock-cells into the
child node, since that is the actual clock provider, and not all
instances of qcom-qmp-phy are clock providers. Also set #clock-cells to
zero, since there's nothing to pass to it.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Utilize the newly fixed up DT bindings to get the tx2 and rx2 register
regions for the second lane of dual-lane PHYs. Before this change,
the driver was simply using lane one's register region and adding
0x400, which reached well beyond the DT-specified register
allocation. This would have been a crash were it not for the page size
on ARM64. Fix the driver not to rely on the magic of virtual memory by
using the newly specified DT register regions for tx2 and rx2.

In order to support existing device trees, this change also contains a
fallback mode for when those new register regions don't exist, which
reverts to the original behavior of overreaching and prints a complaint.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add register regions for the second lane of dual-lane nodes.
This additional specification is needed so that the driver can stop
reaching beyond the tx and rx register allocations to get at the
second lane registers in a dual-lane PHY.

While in there, document #clock-cells as optional for PHYs that don't
provide a pipe clock. Also, document the pcs_misc register region, which
was being quietly supplied and used.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

drivers/phy/ti/phy-gmii-sel.c:91:2-3: Unneeded semicolon

 Remove unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci

Fixes: 1811851f4e73 ("phy: ti: introduce phy-gmii-sel driver")
CC: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The MIPI D-PHY spec defines default values and boundaries for most of the
parameters it defines. Introduce helpers to help drivers get meaningful
values based on their current parameters, and validate the boundaries of
these parameters if needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Now that we have some infrastructure for it, allow the MIPI D-PHY phy's to
be configured through the generic functions through a custom structure
added to the generic union.

The parameters added here are the ones defined in the MIPI D-PHY spec, plus
the number of lanes in use. The current set of parameters should cover all
the potential users.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The phy framework is only allowing to configure the power state of the PHY
using the init and power_on hooks, and their power_off and exit
counterparts.

While it works for most, simple, PHYs supported so far, some more advanced
PHYs need some configuration depending on runtime parameters. These PHYs
have been supported by a number of means already, often by using ad-hoc
drivers in their consumer drivers.

That doesn't work too well however, when a consumer device needs to deal
with multiple PHYs, or when multiple consumers need to deal with the same
PHY (a DSI driver and a CSI driver for example).

So we'll add a new interface, through two funtions, phy_validate and
phy_configure. The first one will allow to check that a current
configuration, for a given mode, is applicable. It will also allow the PHY
driver to tune the settings given as parameters as it sees fit.

phy_configure will actually apply that configuration in the phy itself.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

MIPI D-PHY is a MIPI standard meant mostly for display and cameras in
embedded systems. Add a mode for it.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

This is a cleaned up port of the downstream i.MX8MQ USB3 PHY driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

This adds the binding for the USB3 PHY found on the i.MX8M SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.

For instances using of_node_cmp, this has the side effect of now using
case sensitive comparisons. This should not matter for any FDT based
system which all of these are.

Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add support for port interface mode selection phy (phy-gmii-sel):
- try to request interface mode selection phy from Port DT node and fail
silently if not defined and old CONFIG_TI_CPSW_PHY_SEL driver enabled.
- use new phy if requested successfully.

Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The cpsw-phy-sel driver was replaced with new PHY driver phy-gmii-sel, so
deprecate cpsw-phy-sel bindings and update CPSW binding to use phy-gmii-sel
PHY bindings.

Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

TI am335x/am437x/dra7(am5)/dm814x CPSW3G Ethernet Subsystem supports two
10/100/1000 Ethernet ports with selectable G/MII, RMII, and RGMII
interfaces. The interface mode is selected by configuring the MII mode
selection register(s) (GMII_SEL) in the System Control Module chapter
(SCM). GMII_SEL register(s) and bit fields placement in SCM are different
between SoCs while fields meaning is the same.

Historically CPSW external Port's interface mode selection configuration
was introduced using custom API and driver cpsw-phy-sel.c. This leads to
unnecessary driver, DT binding and custom API support effort.

This patch introduces CPSW Port's PHY Interface Mode selection Driver
(phy-gmii-sel) which implements standard Linux PHY interface and used
as a replacement for TI's specific driver cpsw-phy-sel.c and corresponding
custom API.

Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add CPSW Port's Interface Mode Selection PHY (phy-gmii-sel) DT Bindings

Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Rename the mvebu_comhy_conf structure to be mvebu_comphy_conf, which is
probably what the original author meant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

I noticed that phy_pm_runtime_get_sync() and phy_pm_runtime_put() are not
currently doing anything for phy-mapphone-mdm6600, only the sysfs interface
for works for "auto" and "on".

This is because of the shared GPIO pins between mdm6600 USB port and n_gsm
port. We have not enabled runtime PM for the phy driver until after we've
booted up mdm6600 properly to the USB mode. Otherwise phy_create() would
have called pm_runtime_enable() and pm_runtime_no_callbacks() automatically
on init.

Let's fix this by registering the phy a bit later after we've powered up
the mdm6600 USB port.

And as the PM runtime support is only needed for the n_gsm mode and not for
USB, we can allow the device to idle between phy_mdm6600_power_on() and
phy_mdm6600_power_off(). Note that for suspend, runtime_pm is already
disabled for the phy so we need to check for pm_runtime_enabled().

Cc: Johan Hovold <jhovold@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

This patch modifies rcar_gen3_init_otg() procedure to follow Figure
73.4 of "R-Car Series, 3rd Generation User's Manual: Hardware Rev.1.00".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add a Sierra PHY driver with PCIe and USB support.

The PHY has multiple lanes, which can be configured into
groups, and a generic PHY device is created for each group.

There are two resets controlling the overall PHY block, one
to enable the APB interface for programming registers, and
another to enable the PHY itself.  Additionally there are
resets for each PHY lane.

The PHY can be configured in hardware to read register
settings from ROM, or they can be written by the driver.

The sequence of operation on startup is to enable the APB
bus, write the PHY registers (if required)  for each lane
group, and then enable the PHY.  Each group of lanes
can then be individually controlled using the power_on()/
power_off() function for that generic PHY
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add DT binding documentation for Sierra PHY.  The PHY supports
a number of different protocols, including PCIe and USB.

The PHY lanes may be configured as single or multi-lane links.
Each link is treated as a separate sub-node.  For example, if
there are 4 lanes in total the first 2 might be configured as
a multi-lane PCIe link while the other two are single lane
USB links, and in this case there would be 3 sub-nodes.

There are two resets for the PHY block (one for APB register
access, one for the PHY link) and separate resets for each
link.  For multi-lane links, the reset corresponds to the
reset line on the master lane, the resets on other lanes
have no effect.
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

After recent changes PHY_MODE_SGMII, PHY_MODE_2500SGMII, PHY_MODE_QSGMII,
PHY_MODE_10GKR are not used any more and can be removed. Hence - remove
them.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Convert mvebu-cp110-comphy PHY driver to use recently introduced
PHY_MODE_ETHERNET and phy_set_mode_ext().

Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Convert ocelot-serdes PHY driver to use recently introduced
PHY_MODE_ETHERNET and phy_set_mode_ext().

Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add new PHY's mode to be used by Ethernet PHY interface drivers or
multipurpose PHYs like serdes. It will be reused in further changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Currently the attempt to add support for Ethernet interface mode PHY
(MII/GMII/RGMII) will lead to the necessity of extending enum phy_mode and
duplicate there values from phy_interface_t enum (or introduce more PHY
callbacks) [1]. Both approaches are ineffective and would lead to fast
bloating of enum phy_mode or struct phy_ops in the process of adding more
PHYs for different subsystems which will make them unmaintainable.

As discussed in [1] the solution could be to introduce dual level PHYs mode
configuration - PHY mode and PHY submode. The PHY mode will define generic
PHY type (subsystem - PCIE/ETHERNET/USB_) while the PHY submode - subsystem
specific interface mode. The last is usually already defined in
corresponding subsystem headers (phy_interface_t for Ethernet, enum
usb_device_speed for USB).

This patch is cumulative change which refactors PHY framework code to
support dual level PHYs mode configuration - PHY mode and PHY submode. It
extends .set_mode() callback to support additional parameter "int submode"
and converts all corresponding PHY drivers to support new .set_mode()
callback declaration.
The new extended PHY API
 int phy_set_mode_ext(struct phy *phy, enum phy_mode mode, int submode)
is introduced to support dual level PHYs mode configuration and existing
phy_set_mode() API is converted to macros, so PHY framework consumers do
not need to be changed (~21 matches).

[1] http://lkml.kernel.org/r/d63588f6-9ab0-848a-5ad4-8073143bd95d@ti.comSigned-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

DT bindings normally go in via subsystem maintainers, so add PHY
bindings under generic PHY framework.
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The USB 2.0 PHY on Allwinner H6 SoC is similar to older Allwinner SoCs,
with some USB0 quirk like A83T and PHY index 1/2 missing.

Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The new Allwinner H6 SoC's USB2 PHY has two holes -- USB1 (which is a
3.0 port with dedicated PHY) and USB2 (which doesn't exist at all).

Add support for this kind of missing USB PHY index.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The USB2.0 PHY on Allwinner H6 is similar to the ones on the ones on
older SoCs, but with holes in PHY number (USB1 and USB2 are missing, in
which USB1 is a USB3 PHY).

Add binding for the PHY.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Disabling all EP's allow to reset EP's to initial state.
Introduced new function dwc2_hsotg_ep_disable_lock() which
before calling dwc2_hsotg_ep_disable() function acquire
hsotg->lock and release on exiting.
From dwc2_hsotg_ep_disable() function removed acquiring
hsotg->lock.
In dwc2_hsotg_core_init_disconnected() function when USB
reset interrupt asserted disabling all ep’s by
dwc2_hsotg_ep_disable() function.
This updates eliminating sparse imbalance warnings.

Reverted changes in dwc2_hostg_disconnect() function.
Introduced new function dwc2_hsotg_ep_disable_lock().
Changed dwc2_hsotg_ep_ops. Now disable point to
dwc2_hsotg_ep_disable_lock() function.
In functions dwc2_hsotg_udc_stop() and dwc2_hsotg_suspend()
dwc2_hsotg_ep_disable() function replaced by
dwc2_hsotg_ep_disable_lock() function.
In dwc2_hsotg_ep_disable() function removed acquiring
of hsotg->lock.

Fixes: dccf1bad ("usb: dwc2: Disable all EP's on disconnect")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Up to now the polarity of the over current pin was hard coded to active
high. Use the already defined device tree properties to configure polarity
on i.MX25, too. In difference to i.MX6/7 use active high behavior if the
polarity is unspecified to keep compatibility to existing device trees.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>