- 26 Sep, 2018 40 commits
-
-
Marcel Ziswiler authored
Add GPIO hog to unreset ASIX AX88772B USB Ethernet chip. Signed-off-by:
Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by:
Thierry Reding <treding@nvidia.com>
-
Marcel Ziswiler authored
Add i2c-thermtrip which would set the SLEEP MODE bit in the SUPPLYENE register of the TPS658643 PMIC. Signed-off-by:
-
Marcel Ziswiler authored
Rename and annotate LM95245 temperature sensor more in-line with our other device trees. Signed-off-by:
-
Marcel Ziswiler authored
Add dr_mode property to the USB controller. Signed-off-by:
-
Marcel Ziswiler authored
Add SODIMM pin 45 as GPIO wakeup key. Signed-off-by:
-
Marcel Ziswiler authored
Use high speed UART driver compatible nvidia,tegra20-hsuart. Signed-off-by:
-
Marcel Ziswiler authored
Add UART-C. Signed-off-by:
-
Marcel Ziswiler authored
Annotate UART-A and UART-B. Signed-off-by:
-
Marcel Ziswiler authored
Add display controller parallel RGB panel support incl. backlight PWM. Signed-off-by:
-
Marcel Ziswiler authored
Explicitly add pinmux' for all T20 SoC ball groups now: - Colibri Address/Data Bus (GMI) further pins used as GPIOs - Colibri BL_ON - Colibri EXT_IO* - Colibri L_BIAS, LCD_M1 is muxed with LCD_DE today's display need DE, disable LCD_M1 - more Colibri LCD pins (L_* resp. LDD<*>) - Colibri LCD (Optional 24 BPP Support) - Colibri MMCCD - uart_a_dsr and uart_a_dcd as GPIOs - Colibri USB_CDET - I2C3 (Optional) - JTAG_RTCK - LAN_RESET, LAN_EXT_WAKEUP and LAN_PME (All On-module) - more NAND pins - RESET_OUT - THERMD_ALERT# (On-module), unlatched I2C address pin of LM95245 temperature sensor therefore requires disabling for now Signed-off-by:
-
Marcel Ziswiler authored
Just cosmetic pinmux clean-up. Signed-off-by:
-
Marcel Ziswiler authored
Update sound nvidia,model to be more in-line with our other device trees. Signed-off-by:
-
Marcel Ziswiler authored
Cleaning up indentation, line-feed and white-space. Signed-off-by:
-
Marcel Ziswiler authored
Remove the phy-reset-gpio from the USB controller node as it is already specified in the PHY node. Signed-off-by:
-
Marcel Ziswiler authored
Annotate USB EHCI instances. Signed-off-by:
-
Marcel Ziswiler authored
Add missing regulators: - reg_lan_v_bus being USB Ethernet chip vbus supply - carrier board reg_3v3 to be used as backlight and panel power supply - carrier board HDMI supply being reg_5v0 - reg_usbc_vbus being the USB vbus supply of the EHCI instance 0 Signed-off-by:
-
Marcel Ziswiler authored
Just cosmetic regulator clean-up. Signed-off-by:
-
Marcel Ziswiler authored
Use no-1-8-v property rather than vmmc/vqmmc supplies and drop now obsolete and anyway non-existent vcc_sd. Signed-off-by:
-
Marcel Ziswiler authored
Reorder Host1x/HDMI properties. Signed-off-by:
-
Marcel Ziswiler authored
Add empty local-mac-address property to be filled in by boot loader (e.g. U-Boot). Signed-off-by:
-
Marcel Ziswiler authored
Annotate I2C busses: GEN2_I2C and CAM_I2C (I2C3) being unused and DDC_CLOCK/DATA on X3 pin 15/16 e.g. used for display EDID. Signed-off-by:
-
Marcel Ziswiler authored
Add rtc0 being the ultra low-power I2C one as found on the carrier board and the 3rd UART being NVIDIA's UARTB. Signed-off-by:
-
Marcel Ziswiler authored
Integrate support for GEN1_I2C aka I2C_SDA/SCL on SODIMM pin 194/196 and the M41T0M6 real time clock on the carrier board. Signed-off-by:
-
Marcel Ziswiler authored
Move RTC aliases from module to carrier board to be more in-line with all our other device trees. Signed-off-by:
-
Marcel Ziswiler authored
Drop unused hdmi_ddc label. Signed-off-by:
-
Marcel Ziswiler authored
Shorten temperature-sensor node to just temp-sensor as suggested in the binding documentation. Signed-off-by:
-
Marcel Ziswiler authored
Get rid of the fake clocks simple bus and use node names as per the actual schematics. Signed-off-by:
-
Marcel Ziswiler authored
As underscores in node names are not recommended replace them all where possible with dashes. Signed-off-by:
-
Marcel Ziswiler authored
Drop obsolete spidev device tree nodes as nowadays one should do this by binding the spidev driver to specific instances/chip selects at runtime. Signed-off-by:
-
Marcel Ziswiler authored
Drop model and compatible nodes from the module level device tree as they get overridden by the carrier board device tree anyway. Signed-off-by:
-
Marcel Ziswiler authored
Reorder SD card properties. Signed-off-by:
-
Marcel Ziswiler authored
Reorder CPU DFLL clock properties. Signed-off-by:
-
Marcel Ziswiler authored
Add toradex,apalis-tk1-v1.2 compatible. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Marcel Ziswiler authored
Add mmc-ddr-1_8v property enabling eMMC DDR52 mode. root@apalis-tk1-mainline:~# cat /sys/kernel/debug/mmc2/ios clock: 52000000 Hz actual clock: 52000000 Hz vdd: 21 (3.3 ~ 3.4 V) bus mode: 2 (push-pull) chip select: 0 (don't care) power mode: 2 (on) bus width: 3 (8 bits) timing spec: 8 (mmc DDR52) signal voltage: 1 (1.80 V) driver type: 0 (driver type B) root@apalis-tk1-mainline:~# hdparm -t /dev/mmcblk2 /dev/mmcblk2: Timing buffered disk reads: 256 MB in 3.02 seconds = 84.83 MB/sec Signed-off-by:
-
Marcel Ziswiler authored
Add proper eMMC vmmc and vqmmc supplies e.g. fixing signalling voltage. Signed-off-by:
-
Marcel Ziswiler authored
Reorder backlight properties. Signed-off-by:
-
Marcel Ziswiler authored
White-space clean-up. Signed-off-by:
-
Marcel Ziswiler authored
Drop unused pinmux label. Signed-off-by:
-
Marcel Ziswiler authored
Add missing regulators: - reg_module_3v3_audio being VDDA supply of SGTL5000 - VDDD supply of SGTL5000 actually being reg_1v8_vio - TMP451 temperature sensor vcc supply being reg_module_3v3 - usb3-0 vbus supply being reg_usbh_vbus - usb3-1 vbus supply being reg_usbo1_vbus - carrier board HDMI supply being reg_5v0 - carrier board sata target 5v supply being reg_5v0 - carrier board sata target 12v supply being reg_12v0 - carrier board reg_3v3 actually being backlight power supply Signed-off-by:
-
Marcel Ziswiler authored
Just cosmetic regulator clean-up. Signed-off-by:
-
